En-4
1-888-514-1663 |
WWW.OUTLANDLIVING.COM
LEAK TEST:
1.
DO NOT USE OR PERMIT SOURCES OF IGNITION
IN THE AREA WHILE DOING THE LEAK TEST.
THIS INCLUDES SMOKING.
2.
Leak testing should be done once per year or whenever the
LP gas cylinder or any other gas system part is taken apart,
serviced or replaced, whichever is more frequent.
3. Ensure all gas system coupling joints are tight
and properly attached.
4. Prepare a leak testing solution of half liquid detergent
and half water.
5. Apply the solution to the LP gas delivery system at points as
shown in illustration indicated on page 3.
6.
If parts of the fitting begin to produce bubbles, spray liquid, or
if you smell liquid propane gas, immediately close the valve on
the tank.
7. Wait 5 minutes for any gas to dissipate.
8. After waiting for 5 minutes, the leak(s) must be stopped by
tightening the loose joints, if possible, or by replacing the
faulty parts(s) with the part(s) recommended by the appliance
manufacturer.
THE APPLIANCE IS NOT TO BE USED UNTIL
ANY LEAK IS CORRECTED.
A gas appliance repairman or LP gas dealer should be called if
attempts to stop the leak(s) are unsuccessful and, in such case, the
LP gas supply must be shut off at the cylinder valve or the cylinder
must be removed from the appliance until the leak(s) is corrected.
Inspect hose prior to each use of the unit. The hose assembly
must be replaced prior to the appliance being put into operation
if there is evidence of excessive abrasion or wear, or if the hose
is damaged. Contact FMI Brands Inc. should you require a
replacement hose.
Inspect burner prior to each use. Burner must be replaced prior
to the appliance being put into operation if there is evidence of
damage. Replacement burners are available from FMI Brands Inc.
Inspect the burner tube venturi and ensure the mesh screen is in
place, prior to each use. Insects will build nests in the tube if they
can get in and this can cause a back-flame event! Always clear all
valve and gas orifices of any foreign debris including spider webs
prior to lighting. If any doubt there may be a nest inside, use a pipe
cleaner up the tube.
Should any part of this appliance (including the burner) become
soiled or dirty, wipe lightly with a damp cloth.
Do not use flammable or corrosive cleaning products on or near
this unit.
Keep the appliance area clear and free from combustible
materials, gasoline and other flammable vapors and liquids.
Solid fuels shall not be burned in this appliance.
Installation must conform with local codes or, in the absence of
local codes, with either the National Fuel Gas Code, ANSI Z223.1/
NFPA 54, Natural Gas and Propane Installation Code, CSA B149.1
or Propane Storage and Handling Code, B149.2, or the Standard for
Recreational Vehicles, ANSI A 119.2/NFPA 1192, and CSA Z240 RV
Series, Recreational Vehicle Code, as applicable.
SECTION 1: ASSEMBLY
STEP 1
Enclosed are four bags of rocks, one factory installed 10'
propane-rated hose with attached regulator, and one propane tank
stabilizer ring.
STEP 2
Remove the plastic bags containing the rocks and set
aside the propane stabilizer ring.
STEP 3
Open the two bags containing mid-sized rocks, labelled
conveniently for you “M” and arrange in burner area.
STEP 4
Open the single bag containing larger sized rocks, labelled
conveniently for you “L” and arrange on top of the medium sized
rocks.
Our preferred configuration is
pictured here.
Never handle rocks which
have not been allowed to
cool from exposure to flame.
Never attempt to rearrange
rocks while unit is ignited.
STEP 5
The fourth bag of rocks are included as spares and labelled
“Spare Rocks”. These can be stored and used as replacements.
Note:
• Rocks are not to exceed a maximum weight of 2 kgs or 4.4 lbs.
NOTE TO USER:
Before igniting the unit for the first time, follow steps one
through 5 in the below Ignition section.
