FMI Comfort Flame CRB3624NRA Скачать руководство пользователя

Страница: 15 / 40

www.fmiproducts.com

124972-01C

Installation Items Needed

Before installing heater, make sure you have

the items listed below.

•  external regulator (supplied by installer)
•  piping (check local codes)
•  sealant (resistant to propane/LP gas)
•  equipment shutoff valve *
•  test gauge connection *
•  sediment trap
•  tee joint
•  pipe wrench
•  approved  flexible  gas  line  with  gas  con

nector (if allowed by local codes) (not

provided)

* A equipment shutoff valve with 1/8" NPT

tap is an acceptable alternative to test gauge

connection. Purchase the optional equipment

shutoff valve from your dealer.

For propane/LP units, the installer must

supply an external regulator. The external

regulator will reduce incoming gas pressure.

You must reduce incoming gas pressure to

between 11" and 14" of water. If you do not re-

duce incoming gas pressure, heater regulator

damage could occur. Install external regulator

with the vent pointing down as shown in Figure

14. Pointing the vent down protects it from

freezing rain or sleet.

CAUTION: Use only new,

black iron or steel pipe. Inter

nally-tinned copper tubing may

be used in certain areas. Check

your local codes. Use pipe of

1/2" diameter or greater to allow

proper gas volume to heater. If

pipe is too small, undue loss of

volume will occur.

Installation must include an equipment shutoff

valve, union and plugged 1/8" NPT tap. Locate

NPT tap within reach for test gauge hook up.

NPT tap must be upstream from heater (see

Figure 15 or Figure 16 on page 16, depending

on your model).

Propane/LP

Supply Tank

External

Regulator

with Vent

Pointing

Down

Figure 14 - External Regulator With Vent

Pointing Down

INSTALLATION

Continued

IMPORTANT:

Install equipment shutoff valve

in an accessible location. The equipment

shutoff valve is for turning on or shutting off

the gas to the appliance.
Check your building codes for any special

requirements for locating equipment shutoff

valve to fireplaces.

Apply pipe joint sealant lightly to male NPT

threads. This will prevent excess sealant from

going into pipe. Excess sealant in pipe could

result in clogged heater valves.

WARNING: Use pipe joint

sealant that is resistant to liquid

petroleum (LP) gas.

Figure 15 - Gas Connection

(Thermostatically-Controlled Models Only)

Tee Cap Pipe

Joint

Nipple

3" Minimum

Gas

Regulator

PROPANE/LP

From

External Regulator

(11" W.C.** to 14"

W.C. Pressure)

NATURAL

From

Gas Meter (5" W.C.**

to 10.5" W.C.

Pressure)

Equipment Shutoff Valve

With 1/8" NPT Tap*

Approved

Flexible Gas

Hose (if allowed

by local codes)

Sediment Trap

Содержание Comfort Flame CRB3624NRA









































Результаты поиска

Содержание Comfort Flame CRB3624NRA

Отзывы:

Похожие инструкции для Comfort Flame CRB3624NRA

Бренды по названию

Популярные бренды

FMI Comfort Flame CRB3624NRA, Руководство владельца по эксплуатации и установке

Результаты поиска

Содержание Comfort Flame CRB3624NRA

Отзывы:

Похожие инструкции для Comfort Flame CRB3624NRA

Бренды по названию

Популярные бренды