FMI Comfort Flame CRB3624NRA Скачать руководство пользователя

Страница: 13 / 40

www.fmiproducts.com

124972-01C

INSTALLATION

Continued

Area of Various Standard Round Flues

Diameter

Area

20 sq. inches

29 sq. inches

39 sq. inches

51 sq. inches

Chimney Height

Minimum Permanent

Flue Opening

6' to 15'

39 sq. inches

15' to 30'

29 sq. inches

Damper

Clamp

Damper

Clamp

Damper

Figure 10 - Attaching Damper Clamp

Manufactured Fireplace

Masonry Fireplace

INSTALLING HEATER BASE

ASSEMBLY

WARNING: You must secure

this heater to fireplace floor. If

not, heater will move when you

adjust controls. Moving heater

may cause a gas leak.

WARNING: If installing in a

sunken fireplace, special care

is needed. You must raise the

fireplace floor to allow access

to heater control panel. This

will insure adequate air flow

and guard against sooting and

controls being damaged. Raise

fireplace floor with noncombus

tible material. Make sure material

is secure.

CAUTION: Do not pick up

heater base assembly by burn

ers. This could damage heater.

Only handle base assembly by

grates.

IMPORTANT:

Make sure the heater burners

are level. If heater is not level, heater will not

work properly. For thermostat models, avoid

damage to thermostat bulb. Avoid nicks or

sharp bends in thermostat bulb wire. Keep

thermostat bulb in mounting bracket until

ready to mount base to floor. See

Optional

Positioning Of Thermostat Sensing Bulb

page 30.

Installation Items Needed

• hardware package (provided with heater)

• approved flexible gas hose and fittings (not

provided) (if allowed by local codes)

• sealant (resistant to propane/LP gas, not

provided)

• electric drill with 3/16” masonry drill bit

Note: Install optional Receiver and Hand-Held

Remote Control Kit (see Accessories, page

37) before installing gas log heater (Remote-

Ready Models Only). See installation instruc-

tions included with the kit.

2. State or local codes do not permit vent-

free operation.

3. You prefer vented operation.

If reasons number 1 or 2 apply to you, you

must permanently open chimney flue damper.

You must install the damper clamp accessory

(to order, see

Accessories

, page 37). This

will insure vented operation (see Figure 10).

The damper clamp will keep damper open.

Installation instructions are included with

clamp accessory.

See chart below for minimum permanent flue

opening you must provide. Attach damper

clamp so the minimum permanent flue open

ing will be maintained at all times.

Содержание Comfort Flame CRB3624NRA









































Результаты поиска

Содержание Comfort Flame CRB3624NRA

Отзывы:

Похожие инструкции для Comfort Flame CRB3624NRA

Бренды по названию

Популярные бренды

FMI Comfort Flame CRB3624NRA, Руководство владельца по эксплуатации и установке

Результаты поиска

Содержание Comfort Flame CRB3624NRA

Отзывы:

Похожие инструкции для Comfort Flame CRB3624NRA

Бренды по названию

Популярные бренды