background image

www.fmiproducts.com

126134-01A

14

OPTIONAL GAS LINE INSTALLATION

Continued

  WARNING:  If  the  fireplace 

has been used for wood burn-

ing, firebox and chimney must 

be cleaned of soot, creosote and 

ashes  be  a  qualified  chimney 

cleaner. Creosote will ignite if 

heavily heated.

OPERATION AND MAINTENANCE

Figure 23 - Glass Doors

Cleaning Glass

Clean  glass  with  any  commercial  glass 

cleaner or soap and water. Do not use any 

abrasive material to clean the glass. Do not 

clean glass with any cool water if glass is still 

hot from fire and smoke.
A gas line or gas log lighter may be installed 

for the purpose of installing a vented or vent-

free decorative gas appliance incorporating an 

automatic shutoff device and complying with 

the S

tandard for Decorative Gas Appliances 

for Installation in Vented Fireplaces, ANSI 

Z21.60

 or 

American Gas Association draft 

requirements for Gas Fired Log Lighters for 

Wood Burning Fireplaces, Draft NO. 4

 dated 

August, 1993.
If you wish to install an unvented (vent-free) 

gas log set, only unvented gas log sets which 

have been found to comply with the standard 

for unvented room heaters, ANSI Z21.11.2 are 

to be installed in this fireplace.

  WARNING:  When  using 

a decorative vented gas log, 

damper must be removed or 

permanently locked in fully open 

position and glass doors must 

be in fully open position.

GLASS DOORS

Glass doors are standard with this fireplace. 

When fireplace is in operation, doors must be 

fully opened or fully closed position only or a 

fire hazard may be created (see Figure 23).
A fireplace equipped with glass doors oper

-

ates much differently than a fireplace with an 

open front. A fireplace with glass doors has a 

limited amount of air for combustion. Exces

-

sive heat within fireplace can result if too large 

a fire is built or if combustion air gate is not 

completely open.
The following tips should be used to assure 

that  both  fireplace  and  glass  door  retain 

their beauty and function properly. Both the 

flue  damper  and  glass  doors  must  be  fully 

opened before starting a fire. This will provide 

sufficient  combustion  air  and  maintain  safe 

temperatures in firebox.

IMPORTANT:

  The  glass  must  be  allowed 

to warm slowly and evenly. Tempered glass 

will withstand a gradual temperature rise to 

550° F, which is more than a normal fire will 

generate. Such materials as pitch/wax laden 

logs,  very  dry  mill  end  lumber  and  large 

amounts  of  paper  or  cardboard  boxes  can 

create an excessively hot fire and should not 

be burned in this fireplace. Always keep fire 

back from doors and never allow flames to 

contact glass.

  WARNING:  Fireplaces 

equipped with glass doors 

should be operated only with 

doors fully opened or doors fully 

closed. Doors, if left partly open, 

may draw gas and flame out of 

the  fireplace  opening  creating 

risks of both fire and smoke.

Doors Fully Closed

Doors Fully Opened

Fireplace Front

Fireplace Front

f i r e - p a r t s . c o m

Содержание C42MW-LS





















Отзывы: