background image

Caution:

 If, during a rough landing, the propeller 

on the SkyFly 2 should become jammed and 
cannot rotate with the throttle in the run position, 
the battery and speed control will become very 
hot. Immediately move the throttle stick down to 
stop the motor. If you fail to do this, the motor, 
speed control and/or battery will be damaged.

AFTER THE  FLIGHT

Unplug the battery from the airplane and switch the 
transmitter off. Remove the battery from the battery 
compartment. Allow the motor and battery to cool 
before recharging. Check the airplane over to make 
sure nothing has come loose or may be damaged.

SAFETY CHECKLIST

Always follow this sequence before and after 
each fl ight.

TO FLY:

1. Move throttle slide to the “motor off” position (left).
2. Turn on transmitter and extend antenna.
3. Plug in airplane battery.

AFTER FLIGHT:

1. Move throttle slide to the “motor off” position (left).
2. Unplug battery from the airplane.
3. Turn off transmitter.

REPAIRS

Even the best R/C pilots in the world damage their 
airplanes every now and then. In the unfortunate 
event that you damage your airplane, repairs are 
fairly simple to make yourself. If there are any cracks 
in the wing or fuselage, apply 6-minute epoxy or 
white glue to the broken areas and hold together 
with clear packaging tape. Let the glue cure, leaving 
the tape in place for added strength. 

REPLACEMENT PARTS

To order replacement parts for your SkyFly 2, use 
the order numbers in the parts list. Replacement 
parts are available only as listed. Replacement parts 
are not available from Product Support, but can be 
purchased from hobby shops or mail order/internet 
order fi rms. If you need assistance locating a dealer 
to purchase parts, contact: 

Product Support

Phone: 217-398-0007

Fax: 217-398-7721

E-mail: 

[email protected]

Stock # 

Description

GPMM7702 

12V DC Peak Charger

GPMP7704 

NiMH 8.4V 900mAh Battery

HCAA3875 Wing
HCAA3876 Horizontal 

Stabilizer

HCAA3877 Vertical 

Fin

HCAA3878 Pushrods
HCAA3879 

Main Landing Gear

HCAA3880 

Front Landing Gear

HCAA3881 

Screw Landing Gear (4)

HCAA3882 

Wing Mount Rubber Bands (6)

HCAA3883 

Canopy Rubber Bands (2)

HCAA3884 

Tail Brace Support

HCAA3885 

Vertical Fin Holder

HCAA3886 

Control Horn Set

HCAA3887 Screw-Lock 

Connectors

HCAA3888 

Fuselage w/Tail Boom

HCAA3889 

Vertical Fin Nuts (2)

HCAA3890 Canopy 

Cover

HCAA3891 Motor 

Mount

HCAA3892 

AC Wall Adapter w/Plug

HCAA3893 Propeller 

w/Spinner

HCAG1054 380 

Motor

HCAQ3501 

7x3 Propeller (2)

TACL31A1 

RX/ESC Channel A1

TACL31A2 

RX/ESC Channel A2

TACL31A3 

RX/ESC Channel A3

TACL31A4 

RX/ESC Channel A4

TACL31A5 

RX/ESC Channel A5

TACL31A6 

RX/ESC Channel A6

TACJ31A1 

Tactic 3-Channel Transmitter A1

TACJ31A2 

Tactic 3-Channel Transmitter A2

TACJ31A3 

Tactic 3-Channel Transmitter A3

TACJ31A4 

Tactic 3-Channel Transmitter A4

TACJ31A5 

Tactic 3-Channel Transmitter A5

TACJ31A6 

Tactic 3-Channel Transmitter A6

Содержание Sky Fly 2













Отзывы: