4. Locate the two holes on base plate that match holes of the other
key-slotted bracket and secure bracket to base plate using the
other two nuts and bolts.
5. Remove the two 3/4" threaded nipples, two large nuts and two
hanging rings from hardware package.
6. Screw the nipple into the threaded ends of hanging rings.
7. Insert threaded nipples with hanging ring into key hole slot in
bracket and secure using large nuts.
8. Replace the top hood and the bottom collection tray.
9. Suspend unit from ceiling using chain, hooks, or other suitable
means. See the exploded view on back page for additional
assembly information.
Note:
Collection tray
MODEL CT-850
is available as an
accessory and should be used when unit is ceiling suspended to
collect dead insects that fall from unit’s charged grids.
EXTENSION CORDS:
Appropriate extension cords and devices for retaining an extension
cord connection to the insect killer power cord are available at your
local hardware or home supply store.
Use only three-wire extension cords which have three-prong
grounding type plugs and three-pole receptacles which accept the
products plug.
Replace or repair damaged cords.
Outdoor extension cords must be used with insect killers intended
for outdoor use. Use extension cords marked SJW-A or SJTW-A
and tagged
‘‘suitable for use with outdoor appliances”.
The electrical
rating of the extension cord must be as great as the electrical rating
of the insect killer.
GROUNDING INSTRUCTIONS:
Your insect killer is equipped with an appropri-
ate three-conductor cord and three-prong
grounding type plug to fit the proper grounding
type receptacle. To reduce the risk of an elec-
trical shock, the plug must be plugged into an
appropriate outlet that is properly installed and
grounded.
Your insect killer has a grounding plug that
looks like the plug illustrated, and is intended
for use on a circuit that has an outlet as
shown.
Consult a qualified electrician or serviceman if the grounding in-
structions are not completely understood, or if in doubt as to
whether proper grounding exists.
COLLECTION TRAY:
(see illustration 2)
Your unit is equipped with a sanitary, removable collection tray for
indoor or outdoor use. When vertically mounted, this tray will collect
the dead insects as they fall from the electrically charged grids.
To disengage collection tray at bottom of unit spread the sides of the
tray away from the two mounting clips on the unit base.
To attach collection tray, align the two holes on either side of the
tray with the mounting clips located on the base of the unit. Spread
the sides of the tray and engage the holes in the tray with the clips
on the base.
FLY SEX LURE:
Included with your unit is a specially designed slow-release strip
containing (Z)-9-tricosene, a non-toxic and odorless fly lure, to
substantially increase the effectiveness of the Fly Control Unit.
U.S. Government researches have demonstrated that (Z)-9-tricosene,
a synthetic compound identical to the sex pheromone of house flies
(musca domestica L.) enhances a trap’s effectiveness by a factor of
three to six times that of non-baited traps.
To install the Fly Sex lure, attach the strip to the outer protective grille.
For best results the fly lure slow-release strip should be replaced
every 30 days. FA-5000 are available from your dealer or on-line at
www.flowtron.com
.
When replacing a used lure, wrap it in newspaper and dispose in
trash. Always wash hands thoroughly after contact with the lure strip.
MAINTENANCE:
Other than the recommended cleaning and bulb/starter
replacement, no further maintenance is required.
Cleaning:
Always disconnect the unit from its power source before
servicing.
To reduce the risks of fire, clean your unit frequently. Cleaning
should include the removal of dead insects and insect debris from
the killing grid, bulbs and glow-tube. Clean using a small brush, a
blower such as a portable hair dryer or the exhaust attachment of a
vacuum cleaner.
Do not spray with a water spray or the like.
BULB/STARTER REPLACEMENT: (See Illustration 3)
Your unit uses three BF-130 bulbs, and three F-22 starters, which
may be purchased from your dealer or on-line at
www.flowtron.com.
To replace bulbs or starters, disconnect unit from its power source
and proceed as follows:
1. Remove top cover by unscrewing hanging ring and adjacent
screw.
2. Unplug wiring harness.
3. Remove three sheet metal screws securing glo-tube bulb assem-
bly to top plate.
4. Remove the glo-tube assembly through the top plate.
5. Replace bulb(s).
6. Replace starter, if required.
TRAY REMOVAL
ILLUSTRATION 1
ILLUSTRATION 2
ILLUSTRATION 3
Wall Mount
Wiring
Harness
Mounting
Clip
Ceiling Suspension
(INDOOR ONLY)
GROUNDING
RECEPTACLE
Grounding Pin
BULB REPLACEMENT
Bracket/Pole Mount
Top Cover
Starter
