Fluke ThermoView Series Скачать руководство пользователя

Страница: 40 / 49

Thermal Imager Camera

Accessories

•

Disassemble Ethernet cable connector by loosening nut as shown.

•

Remove cable from RJ45 jack by lifting tab, note wiring for reassembly.

•

Pass Ethernet cable through cable gland on rear

enclosure flange then reassemble connector.

•

Pass power cable end with isolated cable ends

through cable gland on rear enclosure flange.

•

Using Ethernet and power cables that have been

passed through cable glands on rear flange.

•

Install cables onto camera as shown

(turn camera on if needed).

•

Place conduction plate onto inside surface

of enclosure and slide rail onto internal rail.

Now you can move the camera forward.

Internal rail and cables are removed for clarity

•

Secure ground to enclosure using

1x tooth washer, 1x flat washer,

and rail screw from enclosure as shown.

•

Install rear flange onto enclosure by screwing-in

the 6x screws. Then tighten cable glands to

create seal around cables.

Содержание ThermoView Series


















































Результаты поиска

Содержание ThermoView Series

Отзывы:

Похожие инструкции для ThermoView Series

Бренды по названию

Популярные бренды

Fluke ThermoView Series, Руководство пользователя

Результаты поиска

Содержание ThermoView Series

Отзывы:

Похожие инструкции для ThermoView Series

Бренды по названию

Популярные бренды