Fluke ScopeMeter 190 Series III Скачать руководство пользователя страница 7

Страница: 7 / 70

ScopeMeter® Test Tool

Specifications

Specifications

Complete specifications are at

www.fluke.com

. See the

190 Series III Product Specifications

Performance Verification

Warning

To prevent possible electrical shock, fire, or personal injury, do not service the

Test Tool unless you are qualified to do so. Service described in this manual is to

be done only by qualified service personnel.

Table 1

is a list of the available models for the Test Tool.

These performance tests are provided to ensure that the Test Tool is in proper operating

condition. If the Test Tool fails any of the performance tests, calibration adjustment (see

Calibration Adjustment

) and/or repair is necessary.

The Performance Verification Procedure is based on the specification (see

Specifications

The values given here are valid for ambient temperatures between 18 °C and 28 °C.
The Performance Verification Procedure is a quick check of all main specifications for the Test

Tool. Accuracy of Test Tool specifications not tested is linked to those tested in this

verification procedure and is embedded in the Test Tool software. This link is tested

extensively for each new software release.

Table 1. Model Descriptions

Model

Features

190-062-III

Two 60 MHz Scope Inputs (BNC), one Meter Input (banana jack)

190-102-III

Two 100 MHz Scope Inputs (BNC), one Meter Input (banana jack)

190-104-III

Four 100 MHz Scope Inputs (BNC)

190-202-III/190M-2-III

Two 200 MHz Scope Inputs (BNC), one Meter Input (banana jack)

190-204-III/190M-4-III

Four 200 MHz Scope Inputs (BNC)

190-502-III

Two 500 MHz Scope Inputs (BNC), one Meter Input (banana jack)

190-504-III

Four 500 MHz Scope Inputs (BNC)

MDA-550-III

Four 500 MHz Scope Inputs (BNC)

Содержание ScopeMeter 190 Series III







































































Результаты поиска

Содержание ScopeMeter 190 Series III

Отзывы:

Похожие инструкции для ScopeMeter 190 Series III

Бренды по названию

Популярные бренды

Fluke ScopeMeter 190 Series III, Руководство по обслуживанию

Результаты поиска

Содержание ScopeMeter 190 Series III

Отзывы:

Похожие инструкции для ScopeMeter 190 Series III

Бренды по названию

Популярные бренды