manualshive.com logo in svg

Fluke PG9000 Series, Руководство по эксплуатации и обслуживанию

Поделиться
Скачать
Fluke PG9000 Series Скачать руководство пользователя страница 27

 

2.  INSTALLATION 

 

Page 17 

 

© 2011 Fluke Calibration 

 

Caution 

Do not operate  the  AMH with drive pressure lower than 275 kPa (40 psi).  
Damage to the AMH could result. 

o

 

Vacuum  supply

The vacuum pump for the pressure controller of the PG9000 system can be used for the 
AMH vacuum supply 

:  The vacuum supply is necessary for AMH operation when there is vacuum 

in the vacuum chamber (absolute by vacuum mode PG9000 operation).  The vacuum supply 
assures that the binary mass selection pins remain in the correct position and evacuates 
internal AMH volumes to minimize the likelihood of leaks into the reference vacuum. 

Vacuum drive requirements: 

Flow rate:  Very low, avoid restrictions or excessive length of connecting tubing 

Vacuum pressure: 

At least 50 kPa (7.5 psi) under atmosphere 

 Caution 

When using a PG9000 in “absolute by vacuum” mode, do not operate the 
AMH without having a vacuum supply connected to the AMH Vent.  Always 
check  that the AMH  is supplied with vacuum BEFORE  establishing 
reference vacuum in the AMH  bell jar.  Failure to do so may result in 
damage to the binary mass pins and/or binary masses. 

 Caution 

Do not plug the AMH vent  connection. Use only a “SESO” type quick-
connector stem.  Plugging the AMH vent connection will prevent the mass 
pins from retracting, leading to serious damage to  the  AMH internal 
components. 

2.3 

Setup 

2.3.1 

Preparing for Operation 

Note 

Before setting up the PG9000  system, see Section 2.2  for information on 
site requirements. 

 

To prepare PG9000 for operation: 

  Set up the PG9000 Platform (see Section 2.3.1.1). 

  Make the system pressure interconnections (see Section 2.3.1.2). 

  If a manual mass set is being used, set up the manual mass set (see Section 2.3.1.3). 

 

If an optional AMH is being used, set it up with its mass set (see Sections  2.3.1.5  and 
2.3.1.4). 

  If the  PG9000 is to be used with  a  vacuum reference, set up the optional vacuum 

reference hardware (see Section 2.3.1.5).  

 

Содержание PG9000 Series











































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды