Fluke LinkRunner AT 1000 Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 36

background image

Battery Charging and Life

7



Displays the connection type: PoE

, 802.1x

, fiber

. For 802.1x, a green lock indicates authentication

passed, yellow indicates it is not needed, and a red
closed lock indicates it failed authentication.

Battery Charging and Life

To charge the battery, connect the ac adapter to the battery
connector (see Figure 1). You can use the tester while you
charge the battery.

Figure 3 shows how to replace the battery.

When the tester is off, the battery charges in approximately
3 hours.

Note

The battery will not charge if the internal
temperature of the tester is above 113

º

F (45ºC).

The battery life is approximately 6 hours during typical
operation. An icon in the upper-left corner of the screen
shows the battery status.

ffy14.eps

Figure 3. How to Remove the Battery

«
...
13
14
15
16
17
...
»

Содержание LinkRunner AT 1000





































Отзывы:

Нет отзывов

Похожие инструкции для LinkRunner AT 1000

Бренд: Malmet Страницы: 14

Бренд: Zempire Страницы: 2

Бренд: Cameo Страницы: 64

Бренд: Cameo Страницы: 100

Бренд: CAME Страницы: 32

PowerXL DX-NET-ETHERNET2-2

Бренд: Eaton Страницы: 48

Power Xpert C445

Бренд: Eaton Страницы: 2

Бренд: Gamry Instruments Страницы: 69

Бренд: Gamry Instruments Страницы: 30

Бренд: Gamry Instruments Страницы: 88

Бренд: Rayger Страницы: 2

Бренд: Panta Safe Light Страницы: 2

Бренд: Calrec Страницы: 70

Бренд: Pari Страницы: 11

Бренд: Pari Страницы: 2

Бренд: Haas Страницы: 5

Бренд: Bartscher Страницы: 20

Бренд: Bartscher Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды