background image

Dry-well Calibrator

Troubleshooting Problems, Possible Causes, and Solutions

29

Troubleshooting Problems, Possible Causes, and Solutions

This section contains information on troubleshooting, CE Comments, and a wiring diagram.
In the event that the Product appears to function abnormally, this section may help to find and solve the 
problem. Several possible problem conditions are described along with likely causes and solutions. If a 
problem arises, please read Table 

4

 carefully and attempt to understand and solve the problem. If the 

problem cannot otherwise be solved, contact an Authorized Service Center (see 

Contact Fluke 

Calibration

 for assistance. Be sure to have the model number, serial number, voltage, and problem 

description available.

Table 4. Troubleshooting

Problem

Possible Causes and Solutions

Incorrect
temperature reading

Incorrect R0, ALPHA, and DELTA parameters.

 Find the value for R0, 

ALPHA, and DELTA on the Report of Calibration. Reprogram the 
parameters into the Product (see 

Calibration Parameters

). Allow the 

Product to stabilize and verify the accuracy of the temperature reading.

Controller locked up. 

The controller may have locked up due to a power 

surge or other aberration. Initialize the system by performing the Factory 
Reset Sequence.

Factory Reset Sequence. 

Hold 

SET

 and 

EXIT

 down simultaneously while 

powering up the Product. The Product display shows ‘-init-,‘ the model 
number, and the firmware version. Each of the controller parameters and 
calibration constants must be reprogrammed. The values can be found on 
the Report of Calibration (see 

Calibration Parameters

).

The Product heats or 
cools too quickly or too 
slowly

Incorrect scan and scan rate settings.

 The scan and scan rate settings 

may be set to unwanted values. Check the Scan and Scan Rate settings. 
The scan may be off (if the unit seems to be responding too quickly). The 
scan may be on with the Scan Rate set low (if unit seems to be responding 
too slowly).

Improper line voltage.

 Verify the bottom of the unit matches the source 

voltage.

Unstable display

Wait. 

Allow the Product to stabilize for a few minutes.

Proportional band may be incorrect. 

Refer to the proportional band on 

the Report of Calibration.

Содержание 9102S



































Отзывы: