manualshive.com logo in svg

Fluke 1577, Руководство по калибровке

Поделиться
Скачать
Fluke 1577 Скачать руководство пользователя страница 28

1587/1577 

Calibration 

18 

Testing Temperature Function (1587 Only) 

Use the following procedure to verify that the UUT measures temperature within the 

published specification. 
1.

 

Connect the K-Type thermocouple to the temperature input of the UUT (

J

) 

and temperature calibrator.  

Note 

To ensure an accurate measurement the UUT and thermocouple 

connector must be at the same temperature. 

2.

 

After connecting the thermocouple to the UUT and the Calibrator, allow the 

junctions to stabilize before recording the display reading. Depending on 

temperature gradients this could take several minutes. 

3.

 

Turn the rotary switch to 

D

, and press 

G

 to select temperature mode. 

4.

 

Put the calibrator in the thermocouple function, and set the output temperature to 

23 

°

C. 

The UUT display reading should be within the limits of 21.8 

°

C to 24.2 

°

C. 

Testing the Discharge Circuit 

The following Discharge Circuit Test is a safety-related test that verifies input jack 

wiring to the PCA, the RSOB contacts, RSOB pads on the PCA, and other active 

discharge components on the PCA. 

W

 Caution 

To prevent damage to the Test DMM DO NOT press 

t

 

during the following procedure. 

1.

 

Connect the Test DMM to the 

INSULATION

 terminals (+ and -) on the UUT. 

2.

 

Set the Test DMM to measure resistance. 

3.

 

Turn the rotary switch to 

INSULATION

. 

4.

 

Verify that the Test DMM reading is between 2500 

Ω

 and 3500 

Ω

 . 

Testing the Insulation Function 

XW

Warning 

To avoid electric shock hazard at the INSULATION output 
terminals, do not press 

t

 when the rotary switch is set 

to INSULATION. 

W

 Caution 

To prevent damage to the calibrator do not use the 5500A or 
other standard calibrators for the insulation tests.  

W

 Caution 

To prevent damage to the 9100A make sure it is in the 
Insulation Test mode prior to pushing 

t

. 

Insulation Resistance Accuracy Test 

To test the Insulation Resistance accuracy, sequentially complete the test steps in 

Table 4, using the following procedure. 
1.

 

Connect the 

INSULATION

 output terminals on the UUT to the calibrator. 

2.

 

Set the calibrator to the Insulation Resistance Test Mode.  

Содержание 1577







































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды