fluidra Certikin iSAVER+ DVSD03 Скачать руководство пользователя страница 4

Страница: 4 / 12

Technical data

DVSD03

DVSD04

Input Power

1 phase AC

Input Voltage

220-240V

Input Frequency

50Hz

Output Power

Max 1.1kW

Max 2.2kW

Output Voltage

1ph, 0-240V

Phase Type

Single phase

Max. Current

Max 6A

Max. 12A

Speed Range

1200-2900rpm

Cooling

Ventilation

Venti Fan

Gross / Net Weight

3.0 / 2.7kg

Dimensions (HxWxD)

206x110x155mm

Once expired, this product should not be disposed of via general waste, but through a regulated waste disposal and

recycling centre – please consult your local authority for full advice.

List of supplied components

•   inverter
•  Power supply cable (pre-wired into inverter)
•  Mounting template, fixings screws and plugs

Installation

WARNING

Upon receipt of this device, check for any damage which may have occurred in transit. If any

damage is found, DO NOT PROCEED WITH INSTALLATION and contact your supplier for advice.

WARNING

Do not power this device by means of an extension lead.

WARNING

A qualified electrician must carry out all electrical wiring in accordance with local electrical

regulations.

Содержание Certikin iSAVER+ DVSD03













Результаты поиска

Содержание Certikin iSAVER+ DVSD03

Отзывы:

Бренды по названию

Популярные бренды

fluidra Certikin iSAVER+ DVSD03, Руководство пользователя

Результаты поиска

Содержание Certikin iSAVER+ DVSD03

Отзывы:

Бренды по названию

Популярные бренды