fluidra 27802-S3, Руководство по установке и эксплуатации

Страница: 6 / 15

The equipment room should be well ventilated and provided with adequate drainage capabilities so that should an
emergency occur, resulting in flooding from a pipoe, filter or pump, the water can be easily
damage. If drainage cannot be supplied directly from the equipment room, consideration should be given to the
installation of an alternate system to remove water from the mechanical room.
3.2 Filter Installation
Move the filter(s) into place using whatever means available. Be sure to use care if moving by hand. Be careful not to hit
the filter against something solid while positioning. Before continuing, be sure that the filter(s) are in the desired locati
with the connection facing the direction necessary for proper installation. It is also very important to make sure the filter is
sitting on a level hard surface.
It is possible that during transportation, some of the internal components have loosened. It is now necessary to remove
the filter lid and enter the filter, being careful not to break any of the connections. By hand, check the tightness
laterals in the bottom of the filter making sure they are firmly tightened. Also, while in the filter, check for any cracks o
breaks in the body of the filter or the PVC internals that might have occurred during transportation using a flashlight.
Refer to the parts breakdown section at the back of the manual for quantity and location of all accessories for reference
during the installation process.
3.3 Installation of the Pressure Gauge
The pressure gauge will come in a package separate in the box with the filter. Remove all the parts from the bag and
apply teflon tape to all threaded connections. The pressure gauge (1) into the ga
the other side of the gauge tee (2). Slip the rubber washer (4) over
nut (5). Apply teflon tape to the stem of the filter lid and screw the completed gauge assemb
lid.
Fig 3-1
Once the system is started unscrew the tee plug in order to bleed any air that might have been trapped in the
startup.
3.4
Testing of filter
Before adding any sand to the filter, it is very important to test the system with water only!!!
high pressure before leavinbg the factory. It is possible that during transportation, the
1 PRESSURE GAUGE
2 GAUGE TEE
3 TEE PLUG / AIR BLEED
4 RUBBER WASHER
5 GAUGE STEM NUT
The equipment room should be well ventilated and provided with adequate drainage capabilities so that should an
emergency occur, resulting in flooding from a pipoe, filter or pump, the water can be easily
damage. If drainage cannot be supplied directly from the equipment room, consideration should be given to the
installation of an alternate system to remove water from the mechanical room.
to place using whatever means available. Be sure to use care if moving by hand. Be careful not to hit
the filter against something solid while positioning. Before continuing, be sure that the filter(s) are in the desired locati
the direction necessary for proper installation. It is also very important to make sure the filter is
It is possible that during transportation, some of the internal components have loosened. It is now necessary to remove
the filter lid and enter the filter, being careful not to break any of the connections. By hand, check the tightness
laterals in the bottom of the filter making sure they are firmly tightened. Also, while in the filter, check for any cracks o
breaks in the body of the filter or the PVC internals that might have occurred during transportation using a flashlight.
Refer to the parts breakdown section at the back of the manual for quantity and location of all accessories for reference
Installation of the Pressure Gauge
will come in a package separate in the box with the filter. Remove all the parts from the bag and
apply teflon tape to all threaded connections. The pressure gauge (1) into the gauge tee (2). Screw the tee plug (3) into
the other side of the gauge tee (2). Slip the rubber washer (4) over the male end of the tee (2
nut (5). Apply teflon tape to the stem of the filter lid and screw the completed gauge assemb
Once the system is started unscrew the tee plug in order to bleed any air that might have been trapped in the
it is very important to test the system with water only!!!
high pressure before leavinbg the factory. It is possible that during transportation, the filter was damaged. It can be difficult
5
FLUIDRA USA
8525 Mallory Road
Jacksonville, FL 32220
Phone: (904) 378-0999
Fax: (904) 378-0408
PRESSURE GAUGE
TEE PLUG / AIR BLEED
RUBBER WASHER
GAUGE STEM NUT
The equipment room should be well ventilated and provided with adequate drainage capabilities so that should an
emergency occur, resulting in flooding from a pipoe, filter or pump, the water can be easily removed to avoid property
damage. If drainage cannot be supplied directly from the equipment room, consideration should be given to the
to place using whatever means available. Be sure to use care if moving by hand. Be careful not to hit
the filter against something solid while positioning. Before continuing, be sure that the filter(s) are in the desired location
the direction necessary for proper installation. It is also very important to make sure the filter is
It is possible that during transportation, some of the internal components have loosened. It is now necessary to remove
the filter lid and enter the filter, being careful not to break any of the connections. By hand, check the tightness of all the
laterals in the bottom of the filter making sure they are firmly tightened. Also, while in the filter, check for any cracks or
breaks in the body of the filter or the PVC internals that might have occurred during transportation using a flashlight.
Refer to the parts breakdown section at the back of the manual for quantity and location of all accessories for reference
will come in a package separate in the box with the filter. Remove all the parts from the bag and
uge tee (2). Screw the tee plug (3) into
the male end of the tee (2) and thread into the stem
nut (5). Apply teflon tape to the stem of the filter lid and screw the completed gauge assembly onto the stem of the filter
Once the system is started unscrew the tee plug in order to bleed any air that might have been trapped in the filter during
it is very important to test the system with water only!!! All filters are tested with
filter was damaged. It can be difficult