Fluidmesh 2200 Series страница 19 Скачать руководство пользователя | Manualshive

Страница: 19 / 30

background image

19

5.8 Remote Subnets

The remote subnet page shows which custom subnet have been detected behind
remote Fluidmesh units. The units using the default configuration use only IP
addresses of the classes 1.0.0.0 and 2.0.0.0 are not shown in this page.

5.9 Firmware Upgrade

Using this page you can upgrade the Fluidmesh Firmware to the most current version
available.

Download  on  you  PC  the  firmware  upgrade  file  from  the  Fluidmesh  Networks
website.  Select  the  file on  your  hard  disk  and  upload it  on  the  Fluidmesh  unit.  This
operation  might  take  several  minutes.  The  unit  will  automatically  reboot  at  the  end
of the upgrade process.

DO NOT RESTART OR POWER DOWN THE UNIT WHILE UPGRADING THE FIRMWARE.
RESTARTING OR POWERING DOWN THE UNIT BEFORE THE UPGRADE IS COMPLETED
MIGHT DAMAGE THE UNIT.

«
...
17
18
19
20
21
...
»

Содержание 2200 Series































Отзывы:

Нет отзывов

Похожие инструкции для 2200 Series

Бренд: Arris Страницы: 4

Бренд: Belkin Страницы: 104

8760 - Wireless Dual Radio 11a/b/g PoE Access...

Бренд: 3Com Страницы: 8

Бренд: Lancom Страницы: 79

Бренд: TRENDnet Страницы: 127

Бренд: HiTi Digital Страницы: 26

Бренд: Tenda Страницы: 2

Бренд: Digi Страницы: 9

Бренд: Linksys Страницы: 123

MAX-STREAM EA7250

Бренд: Linksys Страницы: 20

Бренд: Acer Страницы: 63

Бренд: Acer Страницы: 38

Predator Connect X5 5G CPE

Бренд: Acer Страницы: 56

Бренд: Acer Страницы: 39

Бренд: Acer Страницы: 7

1130AG - Aironet - Wireless Access Point

Бренд: Cisco Страницы: 48

Бренд: StarTech.com Страницы: 32

Бренд: NETGEAR Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды