flowserve.com
NOTE:
If m
horizontal w
move appr
stroke of th
calibration
a RGGY co
of range on
linkage or r
5.2 Moun
Valve
(See Figure 4
The standard
valve/actuator
volume tanks
a linkage direc
has been desi
between the p
required for th
5
/
32
in. Alle
1
/
2
in. open
7
/
16
in. ope
3
/
8
in. sock
3
/
16
in. nutd
Figure 4: Stan
mounted properl
when the valve
roximately ± 30°
he valve. If mou
error will occur
ode indicating th
n one end of tra
rotate the positi
nting to Sta
es
.)
rotary mountin
r assemblies th
or handwheels
ctly coupled to
igned to allow f
positioner and t
he following pro
en wrench
n-end wrench
en-end wrench
ket with extensi
driver
ndard Rotary M
ly, the follower a
is at 50 % strok
° from horizonta
unted incorrectly
and the indicato
he position sens
avel. Reposition
on sensor to co
ndard Valte
ng applies to Va
hat do not have
s. The standar
the valve shaft
for minimal mis
the actuator. T
ocedure are:
ion
Mounting
Use
arm should be
ke and should
al over the full
y, a stroke
or lights will blin
sor has gone ou
n the feedback
orrect the error.
ek Rotary
altek
e mounted
rd mounting use
ft. This linkage
salignment
The tools
er instructions
nk
ut
es
e
1. Fas
usin
2. Slid
ada
thro
was
light
be t
3. Atta
the
NOT
the
4. Usin
univ
(sta
5. Usin
atta
bolts
6. Rota
slot
nee
the
app
prop
– Digital Positi
sten the spline
ng two 6 x
1
/
2
in
de the take-off a
apter shaft. Ins
ough the take-o
sher and nut. T
tly snug on the
tightened after
ach follower arm
star washer an
TE:
The arm w
free position.
ng four
1
/
4
-20 x
versal bracket u
amped on brack
ng a
1
/
2
in. end w
ch bracket to ac
s slightly loose
ate take-off arm
on the take-of
eded noting the
take-off arm sl
proximately
1
/
16
perly adjusted,
ioner 3200MD
lever adapter t
n. self-tapping s
arm assembly
sert the screw w
off arm and add
Tighten nut with
e shaft but still a
linkage is corr
m to positioner
nd 10-32 nut.
will point up whe
x
1
/
2
in. bolts, f
using appropria
ket).
wrench and two
ctuator transfer
until final adjust
m so the follow
ff arm. Adjust t
e engagement o
lot. The pin sh
in. past the tak
securely tighte
LGENIM0059
to the splined le
screws.
onto the spline
with star washe
d the second st
h socket so arm
able to rotate.
ectly oriented.
r feedback shaf
en feedback sh
fasten positione
ate hole patter
o
5
/
16
-18 x
1
/
2
in.
case pad. Lea
tments are mad
wer pin will slide
the bracket pos
of the follower
hould extend
ke-off arm. Wh
en the bracketi
9-04 09/11
9
ever
e lever
er
tar
m is
This will
ft using
haft is in
er to
n
bolts,
ave these
de.
e into the
sition as
pin and
hen
ing bolts.
