FLORABEST FLB 3000 A1, Перевод оригинального руководства по эксплуатации

Страница: 13 / 89

12
GB
ed by debris from the previous use.
• turn the support (4.1) frame into the correct
position of housing and make sure the sup-
port (4.2) lock in holding fixture (4.3).
When users dismantle the collection bag:
• press the interlock (5.1) to release, if the support
has been released, the user must carry the bag’s
weight alone.
Attention: switch off the vacuum until at
the handle and pull the plug firstly.
Fitting the shoulder harness
(Pic.6)
The Vacuum-Blower is provided with a shoul-
der harness (6.1) this is attached to the top
of the main body of the Vacuum-Blower as
shown (6.2). The shoulder harness is provided
to reduce fatigue and aid comfort when us-
ing the Vacuum-Blower. Never carry the belt
diagonally over shoulder and chest. Wear the
strap only on one shoulder, in this way you
can remove the device in case of danger fast.
Before starting
(fig. 7)
Pull the bracket out of the housing. Connect the
mains cable with the tool’s plug and secure it with
the strain relief bracket (7.1) as shown in Fig 7.
Only connect the device to a power source that
is protected via a residual current protective
device (RCD) with a maximum release current
of 30 mA.
Operation
This leaf blower may be operated only on grids with
a current carrying capacity equal to or greater than
100 A per phase at 230 V nominal voltage.
Starting the vacuum-Blower
(Pic.8, 9 and 10)
To start the Vacuum-Blower ensure that the in-
termediate suction/blower tube is fitted correctly.
Warning!
Before selecting either the Vacuum or Blow
function ensure that the selector lever oper-
ates smoothly and that it is not obstructed
by debris from the previous use.
• Select either the Vacuum or Blow function
using the selector lever on the side of the ma-
chine (8.1) and press the switch button (9.1).
• If more power is required slide the speed control-
ler (10.1) from position “1” to position “Max”.
Stopping the vacuum- Blower
(Pic.11)
To turn off the machine you can simply release
the switch (11.1).
Using the vacuum-Blower
Do not attempt to pick up wet debris, allow fallen
leaves etc, to dry out before using the Vacuum
Blower. The Vacuum-Blower can be used to blow
debris from patios, paths, driveways, lawns,
bushes and borders. It will also pick up leaves,
paper, small twigs and wood chippings. When
the using the Vacuum Blower in Vacuum mode
the debris is sucked up the suction tube before
being ejected into the debris collection bag, as
the debris passes through the suction fan it is
partially shredded. The shredded organic debris
is ideal to use as mulch around plants.
Warning! Any hard objects, such as stones,
tin cans glass etc, will damage the suction fan.
Important
Do not use the Vacuum-Blower to suck up
water or very wet debris.
Never operate the Vacuum-Blower without
the debris collection bag fitted.
Blower mode
Inspect the area to be worked before starting. Remove
any objects or debris that could be thrown, jammed or
become entangled in the Vacuum-Blower.
Select the blow function using the selector lever
on the side of the machine and switch on. With
the Vacuum- Blower resting on its wheels move
the Vacuum-Blower forwards directing the noz-
zle at the debris to be cleared.
Alternatively hold nozzle just above the ground
and swing the machine from side to side, moving
forwards and directing the nozzle at the debris to
be cleared. Blow the debris into a convenient heap
then use the vacuum function to collect the debris.
vacuum mode
Inspect the area to be worked before starting. Remove
any objects or debris that could be thrown, jammed or
become entangled in the Vacuum-Blower.
Select the vacuum function using the selector
lever on the side of the machine and switch on.
i