FLORABEST fhe 550 a1 страница 12 Скачать руководство пользователя

Страница: 12 / 22

A full tank will last for

approx. 10 minutes of

continuous operation.

Check the oil level in good

time.

•

Check the oil fill level and regularly

top up with oil. The oil tank holds

70 ml oil.

• Use Grizzly bio-oil; this product con-

tains additives that reduce wear and

tear and does not damage the pump

system. bio-oil is available from our

Service-Center (see P. 21 for the ad-

dress).

• If you have no Grizzly bio-oil available,

use chain lubrication oil with low adhe-

sive additive content.

1. Unscrew the oil fill cap (23) and

fill up with chain oil.

2. Wipe off any spilled oil and close

the cap again.

Note that the saw can re-oil.

Operation startup

Observe the country-specific and munici-

pal regulations.

Do not work with the high pruning saw

during general ordinary or prescribed

quiet periods.

1. Before starting, check:

- The tension of saw chain 1

- The oil level

- All nuts and screws are sitting firmly

- Only remove blade cover 24 at the

last minute

- Set the working length of the telescop-

ic arm before switching on the equip-

ment

- Check that shoulder strap 12 is in a

comfortable position that eases your

hold on the high pruning saw

- Ensure that you are wearing protec-

tive clothing

- Check that you are standing safely

- Check your working surroundings

2. Switching on

- Connect the equipment to a power

supply with the supply voltage speci-

fied on the rating plate.

- Hold the equipment firmly in a relaxed

and safe manner. Operate starting

lock 11 and switch on the pruning saw

at on/off switch 10.

- The equipment will switch off again

when you release on/off switch 10.

- For safety reasons, a lockable contin-

uous operation setting is not possible.

Adjusting the Telescopic

Handle

The telescopic handle can be infinitely

adjusted using quick release 15. Push the

lever forward as shown in the illustration

then push and pull to adjust the handle

length.

Pull back the lever and so fix the desired

working length of the telescopic handle.

Handle Adjustment

• Loosen pivotal centre 8 and and fixing

the adjustable handle 9 on position.

• Replace the pivotal centre 8 to fixation.

10 min

Содержание fhe 550 a1























Результаты поиска

Содержание fhe 550 a1

Отзывы:

Похожие инструкции для fhe 550 a1

Бренды по названию

Популярные бренды

FLORABEST fhe 550 a1, Перевод оригинального руководства по эксплуатации

Результаты поиска

Содержание fhe 550 a1

Отзывы:

Похожие инструкции для fhe 550 a1

Бренды по названию

Популярные бренды