manualshive.com logo in svg

Floe VSD6500, Инструкция по сборке, Страница: 10 / 12

Поделиться
Скачать
Floe VSD6500 Скачать руководство пользователя страница 10

Fig. 6A

SHEET 10 OF 12

Attach the other end of the cable by lifting the opposite

side of the front cradle and fastening with a 1/2" x 2 1/4"

bolt and nylock nut as shown in Fig. 6B.  Torque to 80

ft/lbs.

Fig. 6D

Fasten the side cables to the lower frame clamps using

1/2" x 5" bolts, flatwashers, and nylock nuts as shown in

Fig. 6C.  Check front corner posts for square.  Torque to

80 ft/lbs.

Fig. 6B

The ball screw side cable is attached to the upper clamp

using a 1/2" x 2 1/4" bolt and nylock nut.  See Fig. 6D.

The other side cable is attached to the upper clamp using
a 1/2" x 2 1/4" bolt and nylock nut as shown in Fig. 6E.
Torque both bolts to 80 ft/lbs.

Locate the cable holder and 4" sheave on the hardware

card.  Wrap the cable around sheave and attach to the
clamp with a 1/2" x 2 1/2" bolt and nylock nut. Cable

holder is placed at approximately 120 degrees from

vertical clockwise (or at a 4:00 position) as shown in Fig.

6A.  Now attach the cable end to the lower clamp with a

1/2" x 2 1/2" bolt and nylock nut as shown in Fig. 6A.

Torque both bolts to 80 ft/lbs.

Fig. 6C

Fig. 6A

Fig. 6E

Fig. 6B

Fig. 6D

Fig. 6E

1/2 x 2 1/4" Bolt

w/ Nylock Nut

1/2 x 2 1/4" Bolt

w/ Nylock Nut

Cable

Holder

1/2" x 2 1/2" Bolt

w/ Nylock Nut

1/2 x 5" Bolt, Flatwashers,

& w/ Nylock Nut

1/2 x 2 1/4" Bolt

w/ Nylock Nut

Fig. 6C

1/2 x 5" Bolt, Flatwashers,

& w/ Nylock Nut

Step 6

Содержание VSD6500













Отзывы:

Нет отзывов