manualshive.com logo in svg

Fleximounts GL44B, Руководство по установке, Страница: 5 / 6

Поделиться
Скачать
Fleximounts GL44B Скачать руководство пользователя страница 5

07

08

Step 6: Insert Wire Rope

H
H

I

9

5

9

I

H

x8

H

x8

I

M8

Screw Ring

C1

C1

I

9

9

10

Stickers towards the outside

10

x12

C1

I

M6

5

8

8

Step 7: Assemble Wire Grids

Pass the wire rope in the axle (5) through the pulley in the fixed plate (8).

Step 8: Place and Attach Wire Grid

Use nuts (H) and flat washers (H) to fix the wire grids and platform supports (9) to the eyebolt 
screw and tighten with M8 socket wrench (I).

Tighten

Tighten

Fine adjustments: move nuts up or 
down to make sure the frame is roughly 
horizontal and each wire is under equal 
tension.

Rough adjustments: make sure the frame 
is roughly horizontal and each wire is under 
equal tension.

Adjust 
Wire 
Rope

Unscrew

Adjust the buckle position so each wire is under equal tension while the frame is suspended.

Wooden Ceiling Joists

Wooden Ceiling Joists

Disassemble the J-bolt and nut (C1) as shown below, then use them to attach the wire grids (10) 
to the platform supports (9). Then reassemble and tighten the nuts to the J-bolt with M6 socket 
wrench (I).

Содержание GL44B







Отзывы:

Нет отзывов