Flavel Raglan Скачать руководство пользователя страница 4 | Manualshive

Страница: 4 / 22

Flavel Raglan Скачать руководство пользователя страница 4

INSTALLATION REQUIREMENTS

Efficiency Declaration

The efficiency of this appliance has been measured as specified in

BS EN 613 : 2001 and the result is 74%.

The gross calorific value of the fuel has been used for this efficiency

calculation.

The test data from which it has been calculated has been certified by Advantica.

The efficiency value may be used in the UK Government’s Standard Assessment

Procedure (SAP) for energy rating of dwellings.

1.1

CONDITIONS OF INSTALLATION

It is the law that all gas appliances are installed only by a CORGI Registered

Installer, in accordance with these installation instructions and the Gas Safety

(Installation and Use) Regulations 1998 as amended. Failure to install appliances

correctly could lead to prosecution. It is in your own interest and that of safety to

comply with the law.

The installation must also be in accordance with all relevant parts of the Local and

National Building Regulations where appropriate, the Building Regulations

(Scotland Consolidation) issued by the Scottish Development Department, and all

applicable requirements of the following British Standard Code of Practice.

1. B.S. 5871 Part 1 Installation of Gas Fires

2. B.S. 6891 Installation of Gas Pipework

3. B.S. 5440 Parts 1 & 2 Installation of Flues and Ventilation

4. I.S 813 : 1996 Domestic Gas Installation, issued by the National Standards

Authority of Ireland.

1.2

FIREPLACE / SURROUND SUITABILITY

The fire must only be installed on a hearth it

must not be installed directly onto

carpet or other combustible floor materials.

The fire is suitable for fitting to non-combustible fire place surrounds and propri-
etary fire place surrounds with a temperature rating of at least 150oc.

If a heating appliance is fitted directly against a wall without the use of a fire

surround or fire place all combustible material must be removed from behind

the trim. Soft wall coverings such as blown vinyl, wall paper etc. could be

affected by the rising hot air and scorching and/or discoloration may result.

Due consideration should be made to this when installing or decorating.

4

«
...
2
3
4
5
6
...
»

Содержание Raglan























Отзывы:

Нет отзывов