Flavel Emberglow FEBC00MN Скачать руководство пользователя страница 4

Supplied By www.heating spares.co  Tel. 0161 620 6677

INSTALLATION REQUIREMENTS

1.1

CONDITIONS OF INSTALLATION

In Great Britain :-

It is the law that all gas appliances are installed only by a CORGI Registered
Installer, in accordance with these installation instructions and the Gas Safety
(Installation and Use) Regulations 1998 as amended.  Failure to install appliances
correctly could lead to prosecution.  It is in your own interest and that of safety to
comply with the law.

The installation must also be in accordance with all relevant parts of the Local and
National Building Regulations where appropriate, the Building Regulations
(Scotland Consolidation) issued by the Scottish Development Department, and all
applicable requirements of the following British Standard Code of Practice.

1. B.S. 5871 Part 3 Installation of Decorative Fuel Effect Gas Fires
2. B.S. 6891 Installation of Gas Pipework
3. B.S. 5440 Parts 1 & 2 Installation of Flues and Ventilation
4. I.S. 813 : 1996 Domestic Gas Installation (Republic of Ireland)

If installing this product into a timber framed building, please consult document
IGE / UP 7, issued by the Institute of Gas Engineers.

In Republic of Ireland :-

No purpose made additional ventilation is normally required for this 
appliance, when installed in G.B.  When Installing in I.E. please consult 
document I.S. 813 : 1996 Domestic Gas Installation, which is issued by the
National Standards Authority of Ireland.  If installing in Northern Ireland,
please consult local building regulations.  Any purpose made ventilation
must be checked periodically to ensure that it is free from obstruction. 

1.2

FIREPLACE / SURROUND SUITABILITY

The fire must only be installed on a hearth it must not be installed directly onto
carpet or other combustible floor materials.
The fire is suitable for fitting to non-combustible fire place surrounds and propri-

etary fire place surrounds with a temperature rating of at least 150oc.
If a heating appliance is fitted directly against a wall without the use of a fire
surround or fire place all combustible material must be removed from behind
the trim.  Soft wall coverings such as blown vinyl, wall paper etc. could be
affected by the rising hot air and scorching and/or discoloration may result.
Due consideration should be made to this when installing or decorating.

4

Содержание Emberglow FEBC00MN






















Отзывы: