background image

WARNING: The appliance is very hot during use. Do not touch the surface of the brew head while in use or heated. Danger 

of burns! 

WARNING: Never leave the brew head unattended while preheating water, especially if there are children nearby. 

WARNING: Do not immerse or wash the entire brew head in water or any other liquid. This may cause electric shock or 

damage the appliance. 

WARNING: Be careful when handling hot water. Danger of scalding!

TO PREVENT SCALDING: - Never move the Flair 58 while the preheat system is on and water is inside the brew head - Water 

can remain hot for a long time after preheating and can present a scalding hazard - Keep the Flair 58 and the brew head 

away from the edge of the work surface and out of the reach of children. Do not remove the brew head until it has fully 

cooled down. 

Save these instructions.

Flair 58 Preheat System Safety and Instruction Guide -  [email protected]

CONTENTS OF THIS MANUAL

 

• Flair 58 Preheat System Introduction

 

• Flair 58 Preheat System Parts

 

• Flair 58 Preheat System Setup

 

• Flair 58 Preheat System Use Instructions

 

• Flair 58 Preheat System Cleaning Instructions

 

• Flair 58 Warranty

Introduction

Your Flair 58 comes equipped with a preheat system on the brewing head that allows users to maintain a constant preheat during and in-between shots 

of espresso. This Preheat System has three temperature tiers:

 

• Low Heat – roughly 85° C (185° F)

 

• Medium Heat – roughly 90° C (194° F)

 

• High Heat – roughly 95° C (203° F)

These temperature tiers are meant to loosely correspond to different roast levels: light, medium and dark but can be used as desired to dial-in your shot 

of espresso for the best taste experience. Your Flair 58 Preheat System is not meant to boil your water, and cannot be used for anything other than its 

intention of maintaining a constant temperature on your brew heat for enhanced thermal control. In all cases, the initial temperature of your brew water 

should be managed with your kettle, prior to pouring into your Flair 58.

Further instructions can be found in our Quick Start Guide, provided with your Flair 58, or online at: https://flairespresso.com/learn. There you will find 

video guides as well as downloads that will aid you in any troubleshooting. As always, if you do experience any issues, please reach out to our customer 

support via the email address at the bottom of each page. 

Page 2

Содержание 58








Отзывы: