manualshive.com logo in svg

FiveFish SK-1DI, Инструкция по сборке

Поделиться
Скачать
FiveFish SK-1DI Скачать руководство пользователя страница 6

Copyright  © 2017 FiveFish Audio

SK-1DI Mic DI Assembly Guide

2. TOOLS & EQUIPMENT REQUIRED

A few basic tools and equipment are required to assemble this kit. These basic tools are not supplied with the kit.

2.1. Soldering Iron and Lead - We recommend a temperature adjustable soldering iron. DO NOT USE A 100 WATT 

SOLDERING GUN. A small to medium-sized soldering tip is required to solder the small parts. You may use Lead-free or 

60/40 lead-based solder. 

2.2  Cutter - You will need a cutter to cut component leads and wires.

2.3. Solder Sucker Pump - If you made a mistake and need to desolder a component, you’ll need one. 

2.4. Multitester - Used for measuring resistance, continuity, and voltages. 

2.5. Magnifier & Lamp - I recommend a clean and well-lighted space for your assembly area.

2.6. Other Tools (not required, but nice to have) - Component lead bender, vise, tweezers, wire stripper.

Содержание SK-1DI
















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды