FiveFish SK-1DI Скачать руководство пользователя страница 45

Страница: 45 / 47

SK-1DI Mic DI Assembly Guide

9. TROUBLESHOOTING INFORMATION

Hey, we’re all human and make mistakes. Hopefully the tips below will help you troubleshoot your SK-1DI Mic Preamp build.

I have no output signal. All LED lights work, and I can hear the relays clicking. The VU Meter also display signals but I don’t hear anything

on the output.

If you are *NOT* using an output transformer, make sure to attach jumper wires across the Output Transformer terminals? See Step 3.16.

When I turn the gain knob clockwise, the sound decreases instead of increasing. At minimum gain setting, I have a very loud output signal.

It’s backwards!

Please review Step 3.15 and look closely at how the wires are connected to the potentiometer. You need to swap the location of your 2 wires if your

gain is backwards.

I hear a popping sound when I switch from DI Instrument to Mic Input. I’m using a Condenser microphone with 48Volt phantom power

switched ON.

Turn OFF 48V Phantom Power switch and wait a few seconds before switching between DI Instrument and Mic Input or vice versa. Otherwise, you

may get a popping sound if you switch between the (2) inputs, AND have 48V Phantom Power turned ON.

Содержание SK-1DI






























Результаты поиска

Содержание SK-1DI

Отзывы:

Бренды по названию

Популярные бренды

FiveFish SK-1DI, Инструкция по сборке

Результаты поиска

Содержание SK-1DI

Отзывы:

Бренды по названию

Популярные бренды