background image

16

EXERCISE INSTRUCTIONS

3. THE COOL DOWN PHASE

This stage is to let your Cardio vascular System and muscles wind down. This is a repeat of the 

warm up exercise e.g. reduce your tempo, continue for approximately 5 minutes. The stretching 

exercises should now be repeated, again remembering not to force or jerk your muscles into 

the stretch. As you get fitter you may need to train longer and harder. It is advisable to train at 

least three times a week, and if possible space your workouts evenly throughout the week.

4. FAULT FINDER

If you do not receive numbers appearing on your computer, please ensure all connections are 

correct.

MUSCLE TONING

To tone muscle while on your exercise cycle you will need to have the resistance set quite high. 

This will put more strai n on your leg muscles and may mean you cannot train for as long as you 

would like. If you are also trying to improve your fitness you need to alter your training program. 

You should train as normal during the warm up and cool down phases, but towards the end of 

the exercise phase you should increase resistance making your legs work harder. You will have 

to reduce your speed to keep your heart rate in the target zone.

WEIGHT LOSS

The important factor here is the amount of effort you put in. The harder and longer you work the 

more calories you will burn. Effectively this is the same as if you were training to improve your 

fitness, the difference is the goal.

USE

The seat height can be adjusted by removing the adjustment knob and raising or lowering the 

seat. There are holes in the seat post allowing for a range of heights. Once the correct height 

has been chosen, refit the adjustment knob and tighten. The tension control knob allows you 

to alter the resistance of the pedals. A high resistance makes it more dif ficult to pedal, a low 

resistance makes it easier. For the best results set the tension while the bike is in use.

Содержание EB-ADA-TFS760




















Отзывы: