Fisher SRT-7072 Скачать руководство пользователя | Manualshive

Страница: 34 / 44

background image

SETTING THE RS-232C OR RS-485 DATA
TRANSFER SPEED

The VCR can be controlled by a computer connected to
the RS-232C connector. It can also be controlled through
a special controller connected to the RS-485 connector.

You must specify which connector (RS-232C or RS-485)
is used. (Refer to “Data Transfer Speed Setup.”)

DIP Switches Setup

The DIP switches need to be set when a computer,
special controller, etc. connected to the RS-232C or
RS-485 connectors is used to control the VCR. Make sure
to turn the VCR power off before setting the DIP switches.

SW No.

1-7: To setup the VCR address (only when using the

RS-485 connector).

œ

Switch 1 is the least significant bit (LSB) and
switch 7 the most significant bit (MSB) (Down: 0,
Up: 1)

Example:

œ

If the address is 1, set switch 1 to the ON side
(up)

œ

If the address is 10, set switches 2 and 4 to the
ON side (up)

œ

If the address is 127, set all the switches to the
ON side (up)

8: Available (Not used)
9: To select the connector used. [232] side (down) for

RS-232C, [485] side (up) for RS-485.

10: To setup the termination (only when using the

RS-485 connector).
OFF side (down): Not terminated

ON side (up): Terminated

NOTE:

œ

Refer to the RS-232C and RS-485 command section or
to the special controller and/or to the computer
instruction manual.

Data Transfer Speed Setup

1

Press the MENU button until the (SET UP 3) menu is
displayed.

@@@@@@@<SET@UP@3>

öALARM@MODE@@@@@@@Y1

öALARM@DURATION@@@20S

öVERTICAL@SYNC@@@@Y

öEXT@TIME@ADJ.@@@@01:00

öTAPE@IN@MODE@@@@@STOP

öTAPE@END@MODE@@@@REW

öTAPE@END@OUT@@@@@-3M

öCLOG@DETECT.@@@@@Y

öSERIES@REC@IN@@@@N

öRS-232C@@@@@@@@@@19200

2

Turn the JOG dial, until the “RS-232C” or “RS-485”
setting is flashing.

NOTE:

œ

The display will depend on the DIP switch 9
setting. When down “RS-232C” is displayed and
when up “RS-485” is displayed.

3

Turn the SHUTTLE ring to set the desired transfer
speed.

4

Press the SEARCH button to save the setting.

RS232C 9-pin connector layout

Pin

number

Signal

Operation

Signal direction

2

RXD

Receive

data

VCR

←

Computer

3

TXD

Send data

VCR

→

Computer

7

RTS

Request

to send

VCR

→

Computer

5

GND

Signal

ground

The signal transmission is compatible with RS-232C
specifications.

1

2

3

4

5

6

7

8

9

10

ON

ADDRESS

ON

OFF

485

232

TERMINATE

ON

OFF

2400

4800

9600

19200

1

5

9

6

RC4QR/U3 (SRT-7072 GB) Tue. June, 29/1999

English

33

«
...
32
33
34
35
36
...
»

Содержание SRT-7072













































Отзывы:

Нет отзывов

Похожие инструкции для SRT-7072

Бренд: MYPIN Страницы: 25

Бренд: XtendLan Страницы: 150

Бренд: dallmeier Страницы: 147

Бренд: Infinite Play Страницы: 8

Бренд: Seco Страницы: 79

Бренд: Night Owl Страницы: 2

Бренд: Night Owl Страницы: 7

Бренд: Divis Страницы: 85

GV102ZRH Series

Бренд: Goodmans Страницы: 42

DS-7208HWI-SV series

Бренд: HIKVISION Страницы: 241

Бренд: Idis Страницы: 79

CHRONO VT-CN1680

Бренд: Vitek Страницы: 68

DS-8000HTI-S Series

Бренд: HIKVISION Страницы: 9

DS-77 NI-SP Series

Бренд: HIKVISION Страницы: 33

DS-7300HI-S Series

Бренд: HIKVISION Страницы: 98

Бренд: Northern Страницы: 186

Бренд: UXD Страницы: 16

Бренд: Dahua Страницы: 501

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды