background image

PROBLEMS AND SOLUTIONS GUIDE

 

PROBLEM

 

POSSIBLE CAUSE

 

SOLUTION

Vehicle does not run 

Undercharged battery 

Charge the battery. A new battery should have been 

 

 

charged for at least 18 hours before using the vehicle for

 

 

the first time. After first-time use, recharge the battery for    

 

 

at least 14 hours after each use. Never charge the battery

 

 

longer than 30 hours. 

 

 

Check all connectors. Make sure the battery connector is

 

 

tightly plugged into the charger connector, and that the  

 

 

 

charger is plugged into the wall.

 

 

Make sure power flow to the wall outlet is “ON”. 

 

Charger is not working 

There is no sure way to tell if your charger is working unless  

 

 

you have a volt meter. If you suspect there is a problem with  

 

 

your charger, contact your local Power Wheels

®

 authorized  

 

 

service center. They can test your charger for you.

 

Tripped thermal fuse 

  The built-in thermal fuse may "trip" and shut down operation 
of the vehicle if the vehicle is overloaded or the driving 
conditions too severe. Once a fuse has "tripped", release the 
button on the handlebar and wait approximately 25 seconds 
before operating the vehicle again. To avoid repeated 
automatic shutdowns, do not overload the vehicle by 
exceeding the 40 lb maximum weight capacity or by towing 
anything behind the vehicle. Do not drive up hills or run into 
fixed objects, which can cause the wheels to stop spinning 
while power is still being supplied to the motors. If a thermal 
fuse continually trips, contact your local Power Wheels

®

 

authorized service center.

 

Loose wires or loose connectors 

Check all wires and connectors. Make sure the battery  

 

 

 

 connector is tightly plugged into the motor connector and that 
there are no loose wires around the motors.

 

Dead battery 

If your battery is old or if you have not followed Battery

 

 

Care instructions, your battery may be dead. If you are

 

 

unsure whether or not the battery is dead, you can have 

 

 

it tested at your local Power Wheels

®

 authorized 

  

service 

center.

 

Electrical switch damage 

 The electrical switches can become corroded due to 
exposure to water or moisture, or can jam due to loose dirt, 
sand or gravel. Contact your local Power Wheels

®

 authorized 

service center for diagnosis and repair. 

 

Motor damage 

Contact your local Power Wheels

®

 authorized service center

 

 

for diagnosis and repair.

IMPORTANT!

 If you experience a problem with your vehicle, first check the Problems and Solutions Guide below. If you still experience a 

problem, please contact Power Wheels

®

 Consumer Relations, toll-free at 

1-800-348-0751

 between 9 AM  - 7 PM (EST) Monday through Friday 

and 11 AM - 5 PM (EST) Saturday. Or, contact your local Power Wheels

®

 authorized service center. For the location nearest you, please visit 

us on-line at 

www.powerwheels.com

, or call 

1-800-348-0751

.

17

J4030pr-0920

17

N

77760pr-0921

Содержание Power Wheels 77760





















Отзывы: