background image

8

Securing Your Infant

• Place your child in the seat. Position the restraint pad

between your child’s legs.

• Fasten the restraint belts to each side of the restraint pad.

Make sure you hear a “click” on both sides.

• Check to be sure the restraint system is securely attached

by pulling it away from your child. The restraint system
should remain attached.

Restraint

Pad

Restraint

Belt

Restraint

Belt

To prevent serious injury or death:

• Always use the restraint until child

is able to climb in and out of the
chair unassisted.

• It is dangerous to use this product

on an elevated surface.

• Never leave child unattended.

WARNING

2

Recline

Select a seat position for your child’s comfort:
Upright or Recline.

Upright

While pressing the button on each side rail, lift the seat back.

Recline

While pressing the button on each side rail, lower the 
seat back.

IMPORTANT!

Before each use, inspect this product for 

damaged hardware, loose joints, missing parts or sharp
edges. DO NOT use if any parts are missing or broken.
Contact Mattel for replacement parts and instructions if
needed. Never substitute parts.

Seat Position

Press 

Button

Press 

Button

Lift

1

To prevent serious injury or death:

Use the upright position only when child
has developed enough upper body
control to sit without leaning forward.

WARNING

Upright

Lower

Set-Up & Use

Содержание LEARNING PATTERNS G5911













Отзывы: