background image

Assembly

• Fit a mirror lens to a mirror housing.

• Insert a #8 x 

1

/

2

" screw through the back of the mirror

housing into the mirror lens. Tighten the screw with a
Phillips screwdriver. Do not over-tighten.

• Repeat this procedure to assemble the other mirror lens

to the remaining mirror housing.

• Fit a mirror housing to a handlebar, as shown.

• Fit and hold a mirror clamp to the other side of 

the handlebar.

• Insert two #8 x 

3

/

4

" screws through the back of the mirror

housing and into the mirror clamp.

• Using a Phillips screwdriver, tighten the screws to hold

the mirror housing upright. Do not over-tighten.

• Repeat this procedure to assemble the remaining mirror

housing to the other handlebar.

Mirror Clamp

Mirror Housing

Mirror Housing

Handlebar

Mirror Lens

37

38

21

• Fit the fender tip onto the front of the fender.

• Insert two #8 x 

3

/

4

" screws through the fender tip and

into the vehicle frame. Tighten the screws with a Phillips
screwdriver. Do not over-tighten.

39

Vehicle
Frame

Fender Tip

Front
Fender 

73218pr-0920.qrk  5/21/01 2:29 PM  Page 21

Содержание FISHER-PRICE 73218





































Отзывы: