manualshive.com logo in svg
background image

• Insert the handle

pin through one
side of the
base/handle,
through the holes
in the back of the
frame and out
through the hole
in the other side
of the base/han-
dle. 

Make sure

the handle pin
“snaps” into
place.

• Pull on the 

handle pin to be
sure it is secure.

11

11

Roll Mode

Roll Mode

Base/Handle

Handle Pin

3

• If you are convert-

ing from the rock
mode, remove 
the handle pin
from the wheel
retainers and 
front wheel.

1

Wheel

Retainer

Wheel

Retainer

Front

Wheel

Handle

Pin

2

Base/Handle

• Rotate the

base/handle 
to the upright
position.

Key

Press & Hold

Roll Button

Horn

Blinker

Blinker

Power/Volume

Switch

• Slide the power/volume switch to      on with low 

volume or;

on with high volume.

Press and hold the roll button

until the blinkers

flash and you hear a fun sound effect. You’re ready
to roll!

- When your child turns the handlebar, the left or 

right blinker flashes, while fun music plays along 
to a dancing light display.

- Turn the key to hear fun motor sounds.
- Press the horn, “beep - beep”.

• Slide the power/volume switch to

to turn power off.

IMPORTANT! 

This product emits flashing lights between

5 - 30 cycles per second in some modes of operation.

Convert to Roll Mode

B2488 RRR Trike Deluxe  4/17/03  2:07 PM  Page 11

Содержание B2488













Отзывы: