manualshive.com logo in svg

Fisher Bioblock Scientific Wheaton Biostir, Руководство пользователя

Поделиться
Скачать
Fisher Bioblock Scientific Wheaton Biostir Скачать руководство пользователя страница 9

 2004 Wheaton Science Products

9

P/N 50083244

Specifications subject to change without prior notice

5.0 

INITIAL INSPECTION

When you receive your new Biostir

, inspect it for any obvious damage that may

have occurred during shipment.  If any damage is found, notify the carrier at
once.  Warranty information is shown in the front of this manual. Check to
confirm that there are no broken switches, displays or missing parts, and that the
unit is not dented or scratched.

5.1 

Installation

Install the unit where there will be adequate room for the unit to operate.  Provide
enough clearance around the unit to maintain safety. Install the unit on a level
surface to make sure vessels don’t slide off the top.

5.2 

Input Power Requirements

This equipment is designed to operate from a 200-240V single-phase AC power
source at 47 to 63 Hz.  The line voltage / fuse label located on the upper rear of
the unit shows the nominal input voltage set for the unit at the factory.   

5.3 

Power Cord Set

This unit has been shipped from the factory with a power line cord that has a plug
appropriate for your area. If the wrong power cord has been shipped for your
particular application, contact your nearest Wheaton Science Products (WSP)
dealer for the proper cord. The Biostir

 has been equipped with a 3-wire

grounding type power cord. The unit is only grounded when it is plugged into an
appropriate receptacle. Do not operate the unit without adequate grounding
protection.

 

Содержание Wheaton Biostir






































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды