Fisher & Paykel SINGLE DISHDRAWER DD24STX6HI Скачать руководство пользователя страница 4

4

SAFETY AND WARNINGS

WARNING!

To reduce the risk of fire, injury to persons or damage when using the appliance, follow the 

important safety instructions listed below. Read all the guidance before using the appliance. 

Servicing

 

z

Do not repair or replace any part of the appliance unless specifically recommended in 

this guide. All other servicing should be undertaken by a Fisher & Paykel trained and 

supported service technician or qualified person.

Installation

 

z

Installation of this DishDrawer™ Dishwasher requires basic mechanical and 

electrical skills.

 

z

Installation must comply with your local building and electricity regulations.

 

z

Remove all packaging materials supplied with the dishwasher.

 

z

Be sure to leave these Instructions with the Customer.

 

z

At the completion of the installation, the Installer must perform the Final Checklist.

 

z

This dishwasher is manufactured for indoor use only.

 

z

Ensure all water connections are turned OFF. It is the responsibility of the plumber and 

electrician to ensure that each installation complies with all Codes and Regulations.

 

z

The DishDrawer™ Dishwasher MUST be installed to allow for future removal from the 

enclosure if service is required.

 

z

The switched power outlet must be outside the dishwasher cavity, so that it is 

accessible after installation.

 

z

Care should be taken when the appliance is installed or removed to reduce the 

likelihood of damage to the power supply cord and hoses.

 

z

If the DishDrawer™ Dishwasher is relocated from one installation site to another it must 

be kept upright to avoid damage from water spillage.

 

z

Ensure only supplied hoses are used for connection. Old hoses should not be reused.

 

z

Failure to install correctly could invalidate any warranty or liability claims.

 

z

If the product is installed in a motor vehicle, boat or similar mobile facility, you must 

bring the vehicle, boat or mobile facility containing the product to the service shop at 

your expense or pay the service technician’s travel to the location of the product. 

SAVE THESE INSTRUCTIONS

The models shown in this installation guide may not be available in all markets and are subject to 

change at any time. For current details about model and specification availability in your country, 

please go to our website www.fisherpaykel.com or contact your local Fisher & Paykel dealer.

Содержание SINGLE DISHDRAWER DD24STX6HI

























Отзывы: