Fisher & Paykel HD30 Скачать руководство пользователя страница 9

Страница: 9 / 22

• Please read the instructions carefully.

• Unpack the downdraft unit and place on a flat protected surface.

• Ensure the voltage (V) and the frequency (Hz) indicated on the serial plate match

• the voltage and frequency of the installation site.

• Check that the area around the installation area is clear of any electrical cables and pipes etc.

• Be aware of kitchen cabinets and splash backs in the area of the downdraft vent system and the cooktop.

Ensure that the area where the downdraft unit rises is free of obstacles. Also be aware performance may be
reduced by strong drafts from windows or doors etc.

• The downdraft unit surfaces can be damaged during installation if grazed or knocked by tools. Please take care

to protect the surfaces during installation.

• Temporarily mark the center of the cooktop according to the information given in the ‘Installation instructions –

Cabinet cutout dimensions’ section.

• The downdraft unit is installed directly behind the cooktop. For easiest installation, install the downdraft vent

system first, then the cooktop.

• Remove any cardboard packaging from within the blower impeller.

2. Prepare the Downdraft Unit for the Intended Blower

Internal Blower

• Remove the 10” (254 mm) blower connection plate from the front of the downdraft unit Fig.1.

• Attach the over counter mounting brackets in place with the two 3/16” (5 mm) screws provided Fig.2.

• Screw the support leg mounting brackets to the side of the downdraft unit using two 5/16” (8 mm) screws

each, do not fully tighten the screws. The brackets are different for the right and the left side. Attach them
with mounting clip (A) pointing up.

Remote Blower

• The downdraft unit comes ready for installation with the 10” (254 mm) remote blower connection plate

installed on the front of downdraft unit and the cover plate installed onto the back.

• To connect the remote blower to the back of the downdraft unit swap the plates over (see Fig. 3 and 4)

• Attach the over counter mounting brackets in place with the two 3/16” (5 mm) screws provided Fig.2.

• Screw the support leg mounting brackets to the side of the downdraft unit using two 5/16” (8 mm) screws

each,

do not fully tighten the screws

. The brackets are different for the right and the left side. Attach them

with mounting clip (A) pointing up.

https://producthelp.fisherpaykel.com/us/Cook/Ventilation/Downdraft/HD36/User_Guide_HD36/05_installation_instructions

Updated: Fri, 28 Jun 2019 03:30:59 GMT

Содержание HD30























Результаты поиска

Содержание HD30

Отзывы:

Похожие инструкции для HD30

Бренды по названию

Популярные бренды

Fisher & Paykel HD30, Руководство по установке

Результаты поиска

Содержание HD30

Отзывы:

Похожие инструкции для HD30

Бренды по названию

Популярные бренды