background image

3

SAFETY AND WARNINGS

IMPORTANT SAFETY INSTRUCTIONS! 

Installation

 WARNING!

Cut Hazard

Take care – some edges are sharp.

Failure to use caution could result in injury or cuts.

 

Checking for transport damage

After removing the packaging, make sure the product is complete and undamaged and that all 
accessories are present. Do not use the appliance if it is visibly damaged. Contact Customer Care.

IMPORTANT!

 

Installation must be performed by a qualified professional in compliance with legislation 

in force in the country of installation. 

 

The packing elements (plastic bags, polystyrene foam, etc.) should be kept out of reach 

of children.

 

Never install the appliance in rooms where the temperature may drop to 0°C or lower. 

 

Customise the water hardness as soon as possible following the instructions in your 

user guide.

 

This appliance can be installed over a built-in oven if the latter is fitted with a cooling 

fan at the rear (maximum microwave power: 3 kW). 

 

Connecting the appliance 

 

Danger! Check that the mains power supply voltage corresponds to the value indicated 

on the rating plate on the bottom of the appliance.

 

Connect the appliance to an efficiently earthed and correctly installed socket with a 

minimum current rating of 10A only.

 

Do not allow children and animals to stop or linger near the appliance when it is pulled 

out of the cabinet.

 

If the power socket does not match the plug on the appliance, have the socket replaced 

with a suitable type by a qualified professional. To comply with safety directives, an 

omnipolar switch with a minimum contact distance of 3 mm must be installed. 

 

Do not use multiple sockets or extensions. 

 

If the power socket does not match the plug on the appliance, have the socket replaced 

with a suitable type by a qualified professional. To comply with safety directives, an 

omnipolar switch with a minimum contact distance of 3 mm must be installed. 

 

Do not use multiple sockets or extensions. 

 

Safety cutout devices must be included in the mains power supply in compliance with 

the installation regulations in the country concerned. 

 

This appliance conforms to EC Regulation 1935/2004 on materials and articles intended 

to come into contact with food.

 

Do not allow children and animals to stop or linger near the appliance when it is pulled 

out of the cabinet-.

 

Do not leave the machine pulled out of the cabinet when it is being used.

 

Do not leave the machine pulled out of the cabinet when it is not needed.

 

Install the machine according to the instructions in the hand book to guarantee there are 

no spills when it is pulled out from the cabinet.

 

The rails fixing panel must have a thickness suited to the fixing screws supplied standard.

 

The panel material must be suited to the machine weight of approximately 25kg. 

 

DISPOSAL 

 

The appliance must not be disposed of with household waste, but taken to an authorised 

waste separation and recycling centre.

IMPORTANT!  

 

SAVE THESE INSTRUCTIONS

Содержание EB76PSX1













Отзывы: