Fisher & Paykel DOUBLE DISHDRAWER DD24DTX6HI Скачать руководство пользователя страница 15

15

SECURE TO CABINETRY VIA BRACKETS (METHOD A)

SECURE TO CABINETRY VIA DRAWER REMOVAL (METHOD B)

Partially open one of the drawers and 
remove the first screw cover from the 
trim moulding.

Secure to cabinetry via the brackets. 
Pre-drilling a pilot hole may be required 
depending on the cabinetry material. 

1

2

3

4

Replace the trim cover and repeat for 
the remaining brackets. 

If fitted in step 2, secure the two top 
brackets to the cabinetry. 

  

1

2

3

4

Using the supplied hex socket and 
a screwdriver, level the DishDrawer™ 
Dishwasher as required. Rotate clockwise 
to increase the height of each leg 
and anticlockwise.
It can help to reduce the loading on the 
feet to assist the adjustment process to 
decrease the height. 

Lift the drawer off the runners and 
carefully set aside on a protected 
surface. Push runners back in.
Take care not to pull drawer out too 
far to prevent any strain on the hoses. 
Where possible, protect the base of the 
tub to prevent damage.  

Secure to cabinetry via all four fixing 
locations in the chassis.

Ensure sound insulation is 

replaced correctly.

If fitted, secure the two top brackets 
to the cabinetry. 

  

Open the lower drawer and press both 
locking tabs back to release.

Содержание DOUBLE DISHDRAWER DD24DTX6HI























Отзывы: