Fisher & Paykel DE7060G1 Скачать руководство пользователя

Страница: 11 / 12

If there are any problems, you must address these before proceeding with normal use. The dryer will
automatically turn off at the end of the cycle if there are no problems.

Before you start, it is a good idea to go through the following checklist:

1. Has the packaging been removed?

2. Is the lint filter correctly in place?

3. Has the power cord been connected to an appropriate power supply and the power turned on?

4. Have you performed the installation test cycle?

Product Specifications

Property

DE7060G

DE7060P

Capacity (kg)*

Dimensions (mm)

Property

DE7060G

DE7060P

Width

600

Depth

571

578

Height

825

Electrical

Property

DE7060G

DE7060P

Volts

220 – 240

Amps (maximum)

https://producthelp.fisherpaykel.com/nz/Dry/Dryers/Vented/DE7060G1/User_Guide_DE7060G1/03_Installation_Instructions

Updated: Mon, 05 Oct 2020 18:08:12 GMT

Содержание DE7060G1













Результаты поиска

Содержание DE7060G1

Отзывы:

Похожие инструкции для DE7060G1

Бренды по названию

Популярные бренды

Fisher & Paykel DE7060G1, Руководство по установке

Результаты поиска

Содержание DE7060G1

Отзывы:

Похожие инструкции для DE7060G1

Бренды по названию

Популярные бренды