427939
12
5.2.2 DE50F56EW Door Switch DE50F56EW:
Measure at the PCB across P103-1 and P103-2 on the PCB edge connector with the harness
connected. The resistance should be 0
with the door closed and infinite with the door open.
5.2.3 Door Switch DE40F56A & DE50F56A:
Measure across the Phase pin of the mains plug and terminal 1 the red wire of the timer, the
resistance should be 0
with the door closed and infinite with the door open.
5.2.4 Door Switch DE40F56A2 & DE50F56A2 Push to Start
Measure across the Phase pin of the mains plug and terminal B4 the brown wire of the timer, the
resistance should be 0
with the door closed and infinite with the door open.
5.2.5 Heater / Thermostat Testing DE50F56EW
Measuring at the control module terminals, between terminal P201 the Orange wire and terminal
P205 the Violet wire the resistance should be 63.85
± 1.28
, and measuring at the control
module terminals, between terminal P201 the Orange wire and terminal P208 the Violet wire the
resistance should be 63.85
± 1.28
Note:
With this measurement, the entire element circuit is being tested, including the thermostat. If
there is no circuit detected, then the element, thermostat and connections at the rear of the cabinet
will need to be checked.
5.2.6 Heater / Thermostat Testing DE40F56AW & DE50F56AW
Measuring at the timer terminals, between terminal 10 the Yellow wire and terminal 4 the Black
wire the resistance should be 31.32
± 1.28
Note: the timer must be in the off position.
Note:
With this measurement, the entire element circuit is being tested, including the thermostat. If
there is no circuit detected, then the element, thermostat and connections at the rear of the cabinet
will need to be checked
5.2.7 Heater / Thermostat Testing DE40F56A2 & DE50F56A2
Push to Start
Measuring at the timer terminals, between terminal B2 the Yellow wire and terminal A2 the Black
wire the resistance should be 31.32
± 1.28
Note: the timer must be in the off position.
Note:
With this measurement, the entire element circuit is being tested, including the thermostat. If
there is no circuit detected, then the element, thermostat and connections at the rear of the cabinet
will need to be checked
6
DISASSEMBLY PROCEDURES
6.1 Timer Knob Removal DE40F56A & DE50F56A
1. Grip firmly and pull forward. Note: Push fit only
2. Replace by matching flat on the timer shaft to corresponding flat in knob insert. Push firmly
into place.
6.2 Control Panel Removal DE40F56, DE50F56
1. Remove the timer knob; refer to sec 6.1 for the DE40F56A & DE50F56A only.
2. With the door closed, remove one screw from either side of control panel.
3. Tilt panel forward from top edge and lift gently upwards to release the locking clips.
Reassemble in the reverse order
6.3 Top Panel removal
1. Remove the control panel, refer to sec 6.2
2. Remove 4 screws from the front edge of panel.
3. Remove the 3 screws from the rear edge of the panel
4. The panel can now be removed.
Reassemble in reverse order
Содержание 92188
