background image

Page 2

For technical questions, please call 1-888-866-5797.

Item 63298 

        

Sa
FE
ty

Op
E

ra
ti

O

n

Maint

E

nanc

E

aSSEM

bl
y

Sa
FE
ty

Op
E

ra
ti

O

n

Maint

E

nanc

E

aSSEM

bl
y

Specifications

Rated Capacity

750 lb

Maximum Lift Height

23"

Wheel Bracket Width

40-3/8" – 56-1/8" (center to center)

iMpOrtant SaFEty inFOrMatiOn

Failure to heed these warnings may result in personal injury and/or property damage:

assembly precautions

1.  Assemble only according to these instructions.  

Improper assembly can create hazards.

2.  Wear ANSI-approved safety goggles and 

heavy-duty work gloves during assembly.

3.  Keep assembly area clean and well lit.

4.  Keep bystanders out of the area during assembly.

5.  Do not assemble when tired or when under the 

influence of alcohol, drugs or medication.

6.  Weight capacity and other product capabilities apply 

to properly and completely assembled product only.

Use precautions

1.  Study, understand, and follow all instructions 

before operating this device.

2.  Do not exceed rated capacity.

3.  Use only on hard, level surfaces.

4.  Center load on Lift platforms.

5.  Only lift tires using Wheel Brackets.

6.  Immediately after lifting load, ensure Lift 

mechanical load holding means is engaged.

7.  Do not move while loaded.

8.  Secure load with appropriate restraint device.

9.  Do not adjust safety valve.

10.  Wear ANSI-approved safety goggles and 

heavy-duty work gloves during use.

11.  Keep clear of load while lifting and lowering.

12.  Lower load slowly.

13.  Do not use for aircraft purposes.

14.  Inspect before every use; do not use 

if parts loose or damaged.

15.  Keep your work area clean and well lit.  

Cluttered work areas invite accidents.

16.  Do not allow anyone on the vehicle while 

using the Lift.  Keep bystanders a safe 
distance away from the vehicle and Lift.

17.  Do not lift more than one vehicle at a time.

18.  Stay alert.  Watch what you are doing, and 

use common sense when operating a jack.  
Do not use a jack while tired or under the 
influence of drugs, alcohol, or medication.  A 
moment of inattention while operating jacks 
may result in serious personal injury.

19.  Store idle jacks out of reach of children 

and other untrained persons.  Jacks are 
dangerous in the hands of untrained users.

20.  Jack service must be performed only by 

qualified repair personnel.  Service or 
maintenance performed by unqualified 
personnel could result in a risk of injury.

21.  When servicing a jack, use only identical 

replacement parts.  Follow instructions in the 
“Maintenance and Servicing” section of this manual.  
Use of unauthorized parts or failure to follow 
maintenance instructions may create a risk of injury.

22.  Maintain labels and nameplates.  These carry 

important information.  If unreadable or missing, 
contact Harbor Freight Tools for a replacement.

23.  Before use, read manufacturer’s instruction 

manual for the vehicle you will lift.

24.  Do not support both ends of the 

vehicle at the same time.

25.  Before lowering the Lift, remove all tools 

and equipment from under the vehicle.

26.  The warnings, precautions, and instructions 

discussed in this manual cannot cover all 
possible conditions and situations that may occur.  
The operator must understand that common sense 
and caution are factors, which cannot be built into 
this product, but must be supplied by the operator.

 SaVE tHESE inStrUctiOnS.

Содержание 63298

















Отзывы: