Installation Basics
allation Basics
If you are new to installing Firstech alarm units, we highly recommend that you thoroughly review this
manual before installing your first unit.
If you are new to installing Firstech alarm units, we highly recommend that you thoroughly review this
manual before installing your first unit.
Key Points to Consider Before Installation
Key Points to Consider Before Installation:
The two remotes are preprogrammed to the unit
Page 5
This system is designed for ease of installation and the two included remotes are preprogrammed. In the
event you may need to program new remotes cycle the ignition ON / OFF five times within seven
seconds and tap the Lock button (half second) on the first remote, and then tap the Lock button (half
second) on the second remote.
Remote Valet Procedure
Page 5
Previous Firstech designed systems allow you to put the vehicle in Valet Mode by tapping the Lock and
Trunk buttons at the same time. This feature requires you to turn the ignition on and then tap the Lock
and Trunk buttons to enter Valet.
Option Menus
Page 11
Page 15
The CM-
2305
option menu differs completely from other Firstech systems. It is important to
familiarize yourself with these as it will save time in most applications.
Option Programmer (FT-OP500-KIT)
Most options on this unit can be programmed with the remote(s) as well as the Option Programmer
(OP500). Please note the system must be disarmed before connecting the OP500. Otherwise, an
“ERROR” message will show on the display of your OP500. Connect the OP500 by unplugging the
antenna and plugging into the blue 4 pin port at the top of the programmer.
Updatable
Firmware
The firmware on the CM-
2305
can be updated using our USB Updater Cable. Sign up on
techfeed.compustar.com for instructions and exclusive dealer access.
4
Remote Code Routine(s)
Remote Code Routine(s)
IMPORTANT:
The remotes are preprogrammed to the control module. In the event that you need to
program the remotes, follow the instructions below.
IMPORTANT:
The remotes are preprogrammed to the control module. In the event that you need to
program the remotes, follow the instructions below.
Programming the Remotes
Programming the Remotes
STEP 1:
Activate Programming mode by turning the ignition key
on
and
off
(between the Acc & On
positions) five times within 7 seconds. The vehicles parking lights will flash once with the successful
completion of this step.
STEP 2:
Within a second after cycling the ignition the 5
th
time, tap the Lock button on the
remote
for a
half second. The parking lights will flash once to confirm the transmitter has been coded.
Programming Multiple Remotes:
After the confirmation flash given
in STEP 2, you can code additional remotes by tapping the Lock
button on the
remote(s)
. The parking lights will flash once confirming
each additional remote. The CM-
2305
can store up to three remotes.
Exiting Programming:
Programming is a timed sequence. If you can
not get the remote(s) to program then the system enters Valet Mode.
The parking lights will flash twice signaling the end of programming
mode.
Placement and Use of Components
IMPORTANT:
The placement and use of components are critical to the performance of this system.
Antenna
The antenna on the CM-
2305
is internal and wired directly to the control module. There is no need to run
a cable up the A pillar unless you are using a different RF Kit.
Shock Sensor
For best results, mount the shock sensor by zip tying it to the vehicles main ignition harness. There is a
small dial on the sensor that ranges from Off to 10. The higher the number on the dial the greater
sensitivity of impact. A small adjustment to the dial can make a significant difference in sensitivity for both
1
st
and 2
nd
stages. Recommended dial settings for most vehicles is somewhere between 2 & 4. The
system begins monitoring the shock sensor 30 seconds after the alarm is armed. Also the alarm LED will
stay solid after arming until the shock sensor is active.
Siren
Option 1-06 will allow you to change the volume of the siren chirps. To adjust duration time when the
alarm has been triggered, change
Option 1-05
– the system default is 30 seconds.
5
