background image

3

TO LOCK THE BATTERY COMPARTMENT

Do not lock the battery compartment until you install the batteries and
test the CO Alarm.

If the unit does not alarm during testing, 
DO NOT lock the battery compartment!
Install new batteries and test again. 
If the CO Alarm still does not alarm, replace
it immediately.

1. Using needle-nose pliers, detach one 

locking pin from the mounting bracket.

2. After batteries are inserted, then push 

the locking pin through the hole near the
battery door latch on the back of the CO
Alarm.

OPTIONAL LOCKING FEATURES

TO LOCK THE MOUNTING BRACKET

1. Using needle-nose pliers, detach one

locking pin from the mounting bracket.

2. Insert the locking pin through the hole on

the back of the CO Alarm as shown in the
diagram.

3. When you attach the CO Alarm to the 

mounting bracket, the locking pin’s head
will fit into a notch on the bracket.

The optional locking features are designed to prevent unauthorized removal of the battery or alarm. It is not necessary to activate the locks in 
single-family households where unauthorized battery or alarm removal is not a concern.

These CO Alarms have two separate locking features: one to lock the battery compartment, and the other to lock the CO Alarm
to the mounting bracket. You can choose to use either feature independently, or use them both.

Tools you will need:  • Needle-nose pliers  • Standard flathead screwdriver.

Both locking features use locking pins, which are molded into the mounting bracket. Depending on which locking features you
use, remove one or both pins from the mounting bracket using needle-nose pliers.

To permanently remove either locking pin, insert a flathead screwdriver between the locking pin and the lock, and pry
the pin out of the lock.

TO UNLOCK THE BATTERY COMPARTMENT

1. Remove the CO Alarm from the 

mounting bracket. If the unit is locked 
to the bracket, see the section 
“To Unlock the Mounting Bracket.”

2. Insert a flathead screwdriver under the

head of the locking pin, and gently pry 
it out of the battery compartment lock.
(If you plan to relock the battery 
compartment, save the locking pin.)

3. To relock the battery compartment,

close the battery door and reinsert 
locking pin in lock.

4. Reattach the CO Alarm to the mounting

bracket.

When replacing the batteries, always test
the Alarm before relocking the battery
compartment.

TO UNLOCK THE MOUNTING BRACKET

1. Insert a flathead screwdriver into the

rectangular cut-out on the mounting
bracket nearest to the locking pin.

2. Pry the CO Alarm away from the 

bracket by pushing up on the screw-
driver and turning the CO Alarm 
counterclockwise (left) at the same
time.

Содержание ONELINK CO511








Отзывы: