Fireye Plant Master Скачать руководство пользователя страница 2

 

 

 

 
 

 
 

 

WARNING 

 

 
 
When this equipment is fitted to an appliance due regard must also be given to the requirements of that appliance. 
 

Before attempting to install, commission or operate this equipment all relevant sections of this document must be read and 
fully understood.  If in doubt about any requirements consult Fireye. 
 
Installation, commissioning or adjustment of this product MUST be carried out by suitably trained engineers or personnel 
qualified by training and experience. 
 
After installation or modifications to the installation all functions of the equipment MUST be checked to ensure safe and 
reliable operation of the control. 

 
The manufacturer of this equipment accepts no liability for any consequences resulting from inappropriate, negligent or incorrect 
installation, commissioning or adjustment of operating parameters of the equipment. Control panels 

must not

 be left uncovered 

while power is on.  If it is essential to do so while rectifying faults only personnel qualified by training and experience should be 
involved. The time any covers are off must be kept to a minimum and warning notices 

must

 be posted. 

 
Before attempting any work on this equipment or any equipment controlled by or connected to this equipment, all related electrical 
supplies

 must

 be isolated. 

 
Safety interlocks 

must not

 be removed or over-ridden.  Any faults once detected 

must

 be corrected before the control is operated. 

 
 
CAUTION –  SOME VERSIONS OF THIS EQUIPMENT CONTAIN A LITHIUM BATTERY  

IN THE DISPLAY UNIT 

 

Safety information

 

WARNING

Failure to observe a WARNING about the equipment described in
this manual can cause property damage, severe injury, or death.

CAUTION

Failure to observe a CAUTION may cause minor injury or damage to
equipment.

The  manufacturer  of  this  equipment  has  a  policy  of  continual  product  improvement  and  reserves  the  right  to  change  the 
specification of the equipment and the contents of this manual without notice. 

Содержание Plant Master





















Отзывы: