Fires of Tradition Torrance Jurastone 4004 Скачать руководство пользователя страница 5 | Manualshive

Страница: 5 / 18

Fires of Tradition Torrance Jurastone 4004 Скачать руководство пользователя страница 5

P

AGE

5

OF

18

F

IRES

OF

T

RADITION

I

NSTALL

I

NSTRUCTIONS

FOR

J

URASTONE

T

ORRANCE

#4004

The fireplace must be

installed off the floor to

account for the height of the
hearth and the riser (the riser
is included with the four piece
slip system). The total height
that the unit must sit at is 4
¾” from the finished floor to
the base of the fireplace. If the
measurement is greater the
unit will sit higher than the
riser, resulting in a gap
between the fireplace and the
riser.

The fireplace front must not

be installed flush with the
wall, as there will not be
enough adjustment in the
front to bring it flush with the
back of the surround. The

fireplace should be installed
so that the Fenderfire face is
no less than 1 3/8” but no
more than 1 7/8” from the
finished

wall.

I f

this

measurement is maintained
you will have 1” of adjustment
outward on the Fender fire
face plate.

Note: If the unit is being installed where there is no room for the fireplace to be re-

cessed into the wall then wall must be framed out. When framing out the wall don't
forget to consider the impact of the taped drywall corners. We suggest that you add
an extra 3” for each side for a total of 6” to the widest part of the mantle (the hearth
not the shelf).

Step #1

Step #2

Installing the Torrance with the 534, 4 pc slip kit &

Fenderfire Front

«
...
3
4
5
6
7
...
»

Содержание Torrance Jurastone 4004



















Отзывы:

Нет отзывов