background image

Page 4 of 6

 

 

ICAF - 

Integrated Compressed Air Foam System

 

Inspection and Maintenance Section

 

 

FM-0723-0-7H

 

Installation 

ICAF system shall be located, installed, or suitably protected 
so  as  to  not  be  subjected  to  mechanical,  chemical,  or  other 
damage  that  could  render  them  inoperative.    Foam 
concentrates  are  subject  to  freezing  or  deterioration  from 
prolonged  storage  at  high  temperatures,  the  system  shall 
therefore be located in a room with ambient temperature from 
40

°

F to 110

°

F (4

°

C to 43

°

C). 

Although  it  is  preferable  to  locate  the  system  outside  the 
protected  area,  in  the  case  where  there  is  no  other 
alternative,  provisions  should  be  made  to  ensure  that  the 
system  is  not  going  to  be  exposed  to  fire  or  mechanical 
damage in a manner that would affect its operation. 

System  shall  also  be  installed  so  that  inspection,  testing, 
recharging,  and  other  maintenance  are  facilitated  and 
interruption to protection is held to a minimum.  

  1.  Install  the  ICAF

  S

ystem  unit,  cylinders  bank  and  foam 

concentrate  tank  according  to  the  technical  data 
supplied. 

Note:  

The  drain  collector  shall  be  connected  to  an  open 

drain.  Do not restrict or reduce drain piping. 

  2.  Install  the  open  nozzles  piping  network  in  accordance 

with the ICAF System's Design Manual (FM-090M-0-01). 

  3.  Install  the  releasing  piping  (if  applicable),  detection  and 

signaling  circuits  in  accordance  with  applicable  NFPA 
standards. 

  4.  Conform  to  local  municipal  or  other  codes  regarding 

installations of fire protection systems. 

  5.  Perform  preliminary  inspection  outlined  below  prior  to 

putting system in service. 

  6.  Put the system into operation as outlined below. 

  7.  Perform  the  annual  inspection  sequence  and  test  each 

detector and alarm unit. 

  8.  If  the  system  does  not  operate  as  it  should,  make  the 

necessary  corrections  according  to  manuals  issued  or 
consult your distributor or 

F

IRE

F

LEX 

Systems Inc. 

  9.  Make  sure  that  the  building  owner  or  a  delegated 

representative  has  received  instructions  regarding  the 
operation of the system. 

Inspections, Tests & Maintenance 

Regular  inspections,  tests,  and  maintenance  should  be 
performed at intervals specified in this document to verify that 
the  ICAF  system  is  in  good  operating  condition  and  that  it 
functions as intended.  Components shall be restored to full 
operational condition following inspection and testing.  

The  frequency  of  the  inspections  may  vary  due  to 
contaminated 

water 

supplies, 

corrosive 

or 

humid 

atmospheres as well as the condition of the air supply to the 
system.    In  addition  to  the  instructions  herewith,  local 
Authority 

Having 

Jurisdiction 

may 

have 

additional 

maintenance,  testing  and  inspection  requirements  which 
must be followed. 

Warning !  

Any  system  maintenance  which  involves  placing 

a  control  valve  or  detection  system  out  of  service  may 
eliminate  the  fire  protection  capabilities  of  that  system.  
Prior  to  proceeding,  notify  all  Authorities  Having 
Jurisdiction.    Consideration  should  be  given  to  the 
employment of a fire patrol in the affected areas. 

RESPONSIBILITY of the Owner: 

  1.  The 

responsibility 

for 

properly 

maintaining 

the 

compressed  air  foam  system shall  be  that  of  the  owner 
of the property. 

  2.  Inspection, 

testing, 

and 

maintenance 

shall 

be 

implemented  in  accordance  with  procedures meeting or 
exceeding those established in this document.  

  3.  These  tasks  shall  be  performed  by 

F

IRE

F

LEX

 

's 

authorized  personnel  who  have  developed  competence 
through training and experience. 

  4.  It is the responsibility of the owner to promptly correct or 

repair  deficiencies,  damaged  parts,  or  impairments 
found  while  performing  the  inspection,  test,  and 
maintenance requirements of this document. 

  5.  Corrections  and  repairs  shall  be  performed  by  qualified 

F

IRE

F

LEX 

's authorized personnel. 

  6.  The  building  owner  shall  not  make  changes  in  the 

occupancy, the use or process, or the materials used or 
stored  in  the  building  without  evaluation  of  the  fire 
protection systems for their capability to protect the new 
occupancy, use, or materials. 

  7.  Where  changes  are  identified,  the  owner  shall  promptly 

take  steps  to  evaluate  the  adequacy  of  the  installed 
system  in  order  to  protect  the  building  or  hazard  in 
question.  Where  the  evaluation  reveals  a  deficiency 
causing a threat to life or property, the owner shall make 
appropriate corrections.  

Содержание ICAF System










































Отзывы:

Похожие инструкции для ICAF System