FireClass 555.800.765 Скачать руководство пользователя страница 7

FireClass

FC410MIO

Fixing Instructions

Doc. version 6.0

7/16

 

Note: 

This device uses one address only on the 

loop (in the case of FireClass Express, 7 addres-
ses will be used).

Cabling

Cables are to be selected in accordance with the 
system design document and the requirements 
of the applicable standards.
Two pairs of connection terminals (L+ and L-) are 
provided on the terminal block. These terminals 
are used for connecting the module onto the 
addressable circuit. The maximum section of
the cable that can be connecte at any one termi-
nal is 2.5mm

2

. The section is calculated based 

on the characteristics of the cable and the load.

Ordering information

FC410MIO: Small Addressable Multi-I/O 
Module.

Recycling information

Customers are recommended to dispose of their 
used equipments (panels, detectors, sirens, and 
other devices) in an environmentally sound man-
ner. Potential methods include reuse of parts or
whole products and recycling of products, com-
ponents, and/or materials.

Waste electrical and electronic 
equipment (WEEE) directive

The manufacturer reserves the right to change 
the technical specifications of this product 
without prior notice.

Note:

1 All  SPUR  inputs  must  be terminated with a 

330 ohm EOL resistor.

2 FireClass console or FireClass Express confi-

guration selection- Style B (Normally Open).

3 *Multiple contacts may be used as needed.
 

Notes:

1 For connection of HVR800s, refer to docu-

ment HVR800 High Voltage Relay Module 
“Installation Instructions” 17A-03-HVR, Issue 
3 or later, or 120.415.528, Issue 5 or later.

2 Relay wiring will be application dependant; 

refer to the system diagram.

In the European Union, this label indi-
cates that this product should NOT 
be disposed of with household 
waste. It should be deposited at an 
appropriate facility to enable 
recovery and recycling.

WARNING

The FC410MIO must not be used 
to switch mains voltages.

CENTRALE FC

FC CONTROLLER

+L1

-L1

03

3

ET

NE

U

GE

S

OVI

TI

S

OP

SI

D

L

A

E

CI

VE

D

TX

E

N

OT

03

3

03

3

NC

NO

*

NC

NO

*

NC

NO

*

INGRESSI SPUR

SPUR INPUTS

PROGRAMMING PORT

PORTA DI PROGRAMMAZIONE

LEFT

HVR800-Treiber

HVR800-Drivers

FC410MIO

Fig. 5: Spur Circuit (Class B) Normally Open 
Contacts, Short Circuit = Alarm

Содержание 555.800.765

















Отзывы: