background image

41

WATER STORAGE TANKS

The solar twin coil tank is used to store hot water heated by the solar system. The 
tank has two internal coils, the solar circuit provides heat through the lower coil 
while the back-up heating system (boiler) will heat the hot water via the upper coil.

Firebird water storage tanks are built from premium quality stainless steel and 
include an electric immersion as standard. 

Sales Code

  

DESCRIPTION

SOL

215

ITK 

Twin Coil Solar Tank, 215 litres

SOL

255

ITK 

Twin Coil Solar Tank, 255 litres

SOL

305

ITK 

Twin Coil Solar Tank, 305 litres

SOL

305

TCT 

Triple Coil Solar Tank, 305 litres

An expansion vessel is necessary to absorb the
expansion of the solar fluid when high temperatures
are reached in the solar collector.
Currently available sizes are 24 and 35 litres. 

Sales Code

  

DESCRIPTION

SOL

018

EXP      18 litre Expansion Vessel

SOL

502

EXP     24 litre Expansion Vessel

SOL

503

EXP      35 litre Expansion Vessel

EXPANSION VESSELS

An automatic air vent should be fitted at the highest
point in the solar circuit system in order to remove air
from the system during commissioning. An isolating
valve should be fitted before the air vent and isolated
once the system has been commissioned.

Sales Code

 

DESCRIPTION

 

SOL

501

AIR Air 

Vent

SOL

505

STP Isolating 

Valve

AIR VENT

OTHER SYSTEM COMPONENTS  

THE FOLLOWING COMPONENTS MAY BE SUPPLIED AS STANDARD ON CERTAIN SOLAR SYSTEM KITS

High grade 1m stainless steel flexi pipes which can be connected
to the flow and return side of the collector array. This saves
the installer having to make complicated pipe bends through
the roof of the house. Fittings can be included to connect the
pipe to the different solar collector types.

Sales Code

 

DESCRIPTION

 

SOL

402

FPP 1m 

Flexi 

Pipe

SOL

001

ELB & SOL

001

FEM 

Fittings for CPK7210-N Flat Plate Collector

SOL

075

ELB & SOL

075

TAP 

Fitings for CVSKC-10 Vacuum Tube and

 

TZ58-1800 Heat Pipe Solar collectors

FLEXI PIPES, 1M

Flexible pre-insulated twin pipe with UV protection
sheath for linking collectors to solar tank.
Saves considerable installation time and money.

Sales Code

 

DESCRIPTION

 

SOL

010

TWP  Insulated Twin Pipe DIN16 – 10m

SOL

015

TWP  Insulated Twin Pipe DIN16 – 15m

SOL

025

TWP  Insulated Twin Pipe DIN16 – 25m

STAINLESS STEEL INSULATED TWIN PIPE

Sales Code

 

DESCRIPTION

 

SOL

505

EXP Intermediatory 

Vessel, 

litre

SOL

512

EXP  Intermediatory Vessel, 12 litre 

INTERMEDIATORY VESSELS

Expansion vessel accessory kit includes
check valve, wall bracket and 1 flexi hose.

Sales Code

 

DESCRIPTION

 

SOL

521

PPK Expansion 

Vessel 

Accessory 

Kit

ACCESSORY KIT - EXPANSION VESSEL 

Anti-scald (mixing) valve must be fitted close to
the hot water outlet of the solar tank so that delivery
to the taps does not exceed 48˚C.

Sales Code

 

DESCRIPTION

 

SOL

504

MIX  Anti-scald Mixing Valve

ANTI-SCALD MIXING VALVE

The heat transfer fluid used in a solar circuit is normally
a mixture of water and a polypropylene glycol anti-freeze.
The glycol anti-freeze also contains an additive to
protect against corrosion and evaporates at higher
temperatures than water to allow higher system
temperatures. Firebird recommends a 40% glycol to
60% water mix to ensure frost protection to circa -25˚C.

Sales Code

 

DESCRIPTION

 

SOL

506

FFL 

Tyfocor L Anti-freeze for CPK7210-N Flat Plate Collector

SOL

507

VFL 

Tyfocor LS Anti-freeze for Tube System

SOLAR ANTI-FREEZE

The pipe flashings provide a tidy solution
for passing solar flow and return pipes
through the house roof.

Sales Code

 

DESCRIPTION

 

SOL

509

TRF 

Pipe flashing; Tiled roof

SOL

510

SRF 

Pipe flashing; Slate roof

SOL

524

VTL 

Glidevale G1 Vent Tile (BBA/IAB Approved)

PIPE FLASHING

ACCESSORIES

Sales Code

 

DESCRIPTION

 

SOL

514

FPC 

Weather-proof Cover for CPK7210-N Flat Plate Collector

SOL

515

VTC  Weather-proof Cover for CVSKC-10 Vacuum Tube Collector

SOL

000

FPS 

Solar Filling & Flushing Pump

SOL

527

RFR Refractometer

SOL

528

CFL 

Solar Cleaning Fluid, 500ml

SOL

000

BOV Blow-off 

Storage 

Vessel

SOL

010

TSV  TSV Lightning Protection (for controller)

SOL

526

RLY 

Auxilary Relay HR230 (for controller)

SPARE PARTS

Product Sales Codes & Spare Parts 

Содержание CPK 7210 N













































Отзывы: