background image

 

 

Specifications 

Model: 

      60803 

Voltage: 

      120 

volts 

Amps: 

      12.5 

amps 

Wattage:      1500 

watts 

Lamp 

Type: 

     Quartz 

Halogen 

Minimum Operational Height:  

7 ft., 11 in. (95 in.) 

Assembled 

Weight: 

   69 

lbs. 

Head Unit Dimensions:   

 

25.6” x 21.6” x 18.1” 

Heater Assembled Dimensions: 

15.75” diameter base, 95” height 

 

Storage 
* Always UNPLUG the unit when not in use. 

Once the head unit has completely cooled, store the heater with the protective vinyl cover on the 

head unit. 
* When heater is not in use for an extended period of time, store in a covered location that is dry and 
out of the weather. Make sure the heater is stored in a location that is out of the way of people and pets 
that may accidentally knock the heater over or damage the appliance. Before storing the heater, make 
sure the electrical cord is coiled and out of the way. 
* When storing, 

ALWAYS

 lower the telescopic pole to its lowest level. This will make it easier to 

store and reduce the risk of any accidental tipping over of the heater. 
 

Maintenance 

Your Infrared Heating System is virtually maintenance free! A minute to wipe down exposed surfaces 
is all it takes to maintain your heater. 
* Head unit and shield: Use a non-abrasive cleaner and a soft cloth to wipe off debris and dirt from the 
exposed surfaces. 

NEVER spray liquids or cleaners into the housing area where the halogen lamp 

is located.

 Do not try to disassemble of clean the inner cavity where the halogen lamp is located. For 

any maintenance on the head unit, please call the toll free customer service hotline. 
* Telescopic pole and curved arm components: These can easily be wiped clean using a non-abrasive 
cleaner and a soft cloth. 
* Base with wheel assembly: Use non-abrasive cleaner and a soft cloth. Any scratches, chips or rust 
spots can be touched up using an exterior matte finish paint. 

 

13 

Содержание 60803

















Отзывы: