English
- 21 -
Note: “Episode is unavailable.” message may be
displayed on the screen if a problem occurs during
the playback.
Searching a Programme
Highlight the Search tab using the navigation buttons
and press the
OK
button. Use the virtual keyboard
to type the letters. Select letters and press the
OK
button. When finished, highlight Search option and
press the
OK
button.
Digital Teletext
Press the “ ” button. The digital teletext information
appears. Operate it with the coloured buttons, cursor
buttons and the
OK
button.
The operation method may differ depending on the
contents of the digital teletext. Follow the instructions
displayed on digital teletext screen.
When the “ ” button is pressed again, the TV returns
to television broadcast.
Software Upgrade
Your TV is capable of finding and updating automatically
via the Aerial signal or over the Internet.
Background search and upgrade mode
While the TV is connected to the Internet, if new software
is found, it downloads the upgrades automatically when
the TV next powers on from standby.
3.00am search and upgrade mode
While the TV is connected to an aerial signal. If
Automatic scanning
in the
Upgrade Options
menu
is enabled, the TV wakes up at 03:00 and searches
broadcast channels for new software upgrades. If
new software is found and downloaded successfully,
the next time the TV powers up , it will have the new
software version.
Note.
If the TV fails to come on after the upgrade unplug
the TV for 2 minutes and plug in again.
Troubleshooting & Tips
No power
If your TV has no power, please check the power cord plug
is connected to the mains power socket.
No picture
1.
No Picture means that your TV is not receiving a
transmission. Have you selected the correct button on the
remote control? Try once more. Also make sure the correct
input source has been selected.
2.
Is the aerial connected properly?
3.
Are the plugs connected to the aerial socket?
4.
Is the aerial cable damaged?
5.
Are suitable plugs used to connect the aerial?
6.
If you are in doubt, consult your dealer.
No sound
1.
Has the TV been set to mute? To cancel mute, press the
“ ” button, or increase the volume level.
2.
Sound is coming from only one speaker. Is the balance
set to one extreme? See Sound Menu section.
Remote control - does not operate
Your TV no longer responds to the remote control. The
batteries may be exhausted, if so you may need to replace
the old battieries.
Input sources - can not be selected
1.
If you cannot select an input source, it is possible that
no device is connected.
2.
Check the AV cables and connections if you have tried
to connect a device.
Recording Unavailable
To record a programme, you should first connect a USB
disk to your TV while the TV is switched off. You should then
switch on the TV to enable recording feature. Otherwise,
the recording feature will not be available. If you cannot
record, try switching off the TV and then re-inserting the
USB device while the TV is switched off.
USB Is too Slow
If a “USB is too slow” message is displayed on the screen
while starting a recording, try restarting the recording. If
you still get the same error, it is possible that your USB
disk does not meet the speed requirements. Try connecting
another USB disk.
Internet Connection Not Available / DLNA Mode Not
Operating
If the MAC address (a unique identifier number) of your PC
or modem has been permanently registered, it is possible
that your TV might not connect to the internet. In such a
case, the MAC address is authenticated each time when
you connect to the internet. This is a precaution against
unauthorized access. Since your TV has its own MAC
address, your internet service provider cannot validate
the MAC address of your TV. For this reason, your TV
cannot connect to the internet. Contact your internet service
provider and request information on how to connect a
different device, such as your TV, to the internet.
It is also possible that the connection may not be available
due to a firewall problem. If you think this causes your
problem, contact your internet service provider. A firewall
might be the reason of a connectivity and discovery
problem while using the TV in DLNA mode or while
browsing via DLNA.
Invalid Domain
Ensure that you have already logged on to your PC with an
authorized username/password and also ensure that your
domain is active, prior to sharing any files in your DLNA
server program on your PC. If the domain is invalid, this
might cause problems while browsing files in DLNA mode.
