manualshive.com logo in svg

Finish Thompson MSDB Series, Руководство по сборке, установке и эксплуатации

Поделиться
Скачать
Finish Thompson MSDB Series Скачать руководство пользователя страница 2

2

2 

EU Declaration of Conformity

 

Finish Thompson Inc. hereby declares that the following machine(s)  fully comply with the applicable 

health and safety requirements as specified  by the EU Directives  listed.  The product may not be 

taken into service until it has been  established that  the drive motor  for the centrifugal  pump 

complies  with the provisions  of all relevant  EU Directives.   The complete product complies with the 

provisions  of the EC Directive on machinery  safety provided motors carry CE marking. 

This  declaration  is valid provided that the devices are fully  assembled  and no modifications  are 

made to these devices. 

Type  of Device:

 

Centrifugal Pumps 

Models:

 

AC/AK/AV - 400/500/600/800 

GP-11/22/32 

VKC-5.5/6/6H/7/8/10 

DB-3/4/5/5.5/6/6H/7/8/9/10/11/15/22 

MSKC  

SP-10/11/15/22 

KC-3/4/5/5.5/6/6H/8/10/11/22/32  

MSVKC 

   MSDB 

EU Directives:

 

Machinery Safety (2006/42/EC) 

Applied Harmonized Standards:

 

EN ISO 12100 

EN 809 

Manufacturer:  Finish Thompson Inc. 

921 Greengarden  Road 

Erie, Pennsylvania 16501-1591 U.S.A 

Signed, 

President 

1 July 2020 

Person(s) Authorized  to Compile Technical File:  Finish Thompson GmbH 

Otto-Hahn-Strasse 16 

Maintal, D-63477 DEU 

Telephone:  49 (0)6181-90878-0 

Содержание MSDB Series
































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды