Finish Thompson DB11 series Скачать руководство пользователя страница 3

Страница: 3 / 22

EU Declaration of Conformity

Manufactured by:

Finish Thompson, Inc.

921 Greengarden Road

Erie, Pennsylvania 16501 U.S.A.

Phone: 1-(814)-455-4478

Fax

1-(814)-455-8518

Email:

[email protected]

Web:

www.finishthompson.com

Finish Thompson declares under our sole responsibility that the product listed below conforms to the relevant

provisions of EU directive

2014/34/EU of 26 February 2014

for equipment and protective systems intended for use in

potentially explosive atmospheres, and is certified for safe use in

Atmosphere Group IIC/IIIC category 2

areas.

This declaration applies to Finish Thompson, Inc

ATEX DB Series

pumps only manufactured out of carbon fiber filled

PVDF with a conductive motor adapter and non-sparking ring designated by the letter

“V”

and

“A”

in the model

number. Pumps and their model number may also contain many different combinations of bushings, shafts, o-rings, port

connections, impellers, magnet sets, motor adapters and other options.

Models:

DB6V-A, DB6HV-A, DB7V-A, DB8V-A, DB9V-A, DB10V-A, DB11V-A, DB15V-A & DB22V-A.

This product has used the following harmonized standards to verify conformance:

Non-electrical equipment for potentially explosive atmospheres:

EN ISO 80079-36:2016

Basic Methods and Requirements.

Non-electrical equipment intended for use in potentially explosive atmospheres:

EN ISO 80079-37:2016

Protection by construction safety “ch.” and control of ignition source “bh”

This product must not be used in areas other than specified above. If in doubt consult an authorized distributor,

or refer to the manufacturer Finish Thompson.

Approved by:

Date: 5/5/2017

1026

II 2GD

Ex h IIC T6…T4 Gb

Ex h IIIC T6…T4 Db

FTZU 06 ATEX A136-06 FTZU 08 ATEX A174-08

FTZU 07 ATEX A166-07

Содержание DB11 series























Результаты поиска

Содержание DB11 series

Отзывы:

Бренды по названию

Популярные бренды

Finish Thompson DB11 series, Руководство по сборке, установке и эксплуатации

Результаты поиска

Содержание DB11 series

Отзывы:

Бренды по названию

Популярные бренды